- 您现在的位置：买卖IC网 > PDF目录9527 > DS229SN+ (Maxim Integrated Products)IC TXRX RS-232 TRIPLE 20-SOIC PDF资料下载
参数资料
| 型号： | DS229SN+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 3/9页 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS-232 TRIPLE 20-SOIC |
| 标准包装： | 37 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 3/3 |
| 规程： | RS232 |
| 电源电压： | 4.5 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 管件 |
DS229
3 of 9
V-: Negative supply output (RS-232). V- requires an external storage capacitor of at least 0.1
F. A
larger capacitor (up to 10
F) can be used to reduce supply ripple.
T1IN, T2IN, T3IN: Standard TTL/CMOS inputs for the RS-232 drivers. The inputs of unused drivers can
be left unconnected since each input has a 400 k
pullup resistor.
T1OUT, T2OUT, T3OUT: Driver outputs at RS-232 levels. Driver output swing meets RS-232 levels for
loads up to 3 k
. These driver outputs provide current necessary to meet RS-232 levels for loads up to
2500 pF.
R1IN, R2IN, R3IN: Receiver inputs. These inputs accept RS-232 level signals (±25 volts) into a protected
5 k
terminating resistor. Each receiver provides 0.5V hysteresis (typical) for noise immunity.
R1OUT, R2OUT, R3OUT: Receiver outputs at TTL/CMOS levels.
C1+, C1-, C2+, C2-: Charge pump capacitor inputs. These pins require two external capacitors (0.1
F
minimum, 10
F maximum and should be the same size as C3 and C4). Capacitor 1 is connected between
C1+ and C1-. Capacitor 2 is connected between C2+ and C2-. Capacitor C1 can be omitted if +12 volts is
connected directly to V+. Likewise, C2 can be omitted if -12V is connected directly to V-.
DUAL CHARGE PUMP CONVERTERS
The DS229 has a two stage on-board charge pump circuit that is used to generate
±10 volts from a single
+5-volt supply. In the first stage, capacitor C1 doubles the +5V supply to +10 volts which is then stored
on capacitor C3. The second stage uses capacitor C2 to invert the +10V potential to -10V. This charge is
then stored on capacitor C4. The
±10-volt supplies allow the DS229 to provide the necessary output
levels for RS-232 communication. The DS229 will operate with charge pump capacitors as low as 0.1
F. Larger capacitors (up to 10 F) can be used to reduce supply ripple.
RS-232 DRIVERS
The three RS-232 drivers are powered by the internal
±10-volt supplies generated by the on-board charge
pump. The driver inputs are both TTL and CMOS compatible. Each input has an internal 400 k
=pullup
resistor so that unused transmitter inputs can be left unconnected. The open circuit output voltage swing
is from (V+ - 0.6) to V- volts. Worst case conditions for EIA-232E/V.28 of
±5 volts driving a 3 k=load
and 2500 pF are met at maximum operating temperature and VCC equal to 4.5 volts. Typical voltage
swings of
±8 volts occur when loaded with a nominal 5 k=RS-232 receiver. As required by EIA-232E
and V.28 specifications, the slew rate at the output is limited to less than 30 volts/
s. Typical slew rates
are 20 volts/
s unloaded and 12 volts/s with 3 k=and 2500 pF load. These slew rates allow for bit rates
of over 116 kbits/s. Driver outputs maintain high impedance when power is off.
RS-232 RECEIVERS
The three receivers conform fully to the RS-232E specifications. The input impedance is typically 5
k
=and can withstand up to ±30 volts with or without V
CC applied.
The input switching thresholds are
within the
±3-volt limit of RS-232E specification with an input threshold low of 0.8 volts and an input
threshold high of 2.4 volts. The receivers have 0.5 volts of hysteresis (typical) to improve noise rejection.
The TTL/CMOS compatible outputs of the receivers will be low whenever the RS-232 input is greater
than 2.4 volts. The receiver output will be high when the input is floating or driven between +0.8 volts
and -25 volts.
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B7M-MY-S | CONVERTER MOD DC/DC 10V 50W |
| D38999/20KG11SN | CONN RCPT 11POS WALL MNT W/SCKT |
| VE-B7L-MY-S | CONVERTER MOD DC/DC 28V 50W |
| DS276+ | IC TXRX LO-PWR DPLX RS232 8-DIP |
| MS27505E21B41PA | CONN RCPT 41POS BOX MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS229SN+ | 功能描述:RS-232接口集成电路 RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
| DS22B57 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 SRAM |
| DS22B57S | 制造商:未知厂家 制造商全称:未知厂家 功能描述:x8 SRAM |
| DS22EV5110 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:DVI, HDMI Extended Reach Equalizer with Retimer and Output De-Emphasis |
| DS22EV5110-EVKC | 功能描述:DEMO KIT CAT5 EXTENDER HDMI RoHS:否 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
发布紧急采购，3分钟左右您将得到回复。