- 您现在的位置：买卖IC网 > PDF目录11736 > DS2401X1-S#T (Maxim Integrated Products)IC SILICON SERIAL NUMBER 2CSP PDF资料下载
参数资料
| 型号： | DS2401X1-S#T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | IC SILICON SERIAL NUMBER 2CSP |
| 标准包装： | 2,500 |
| 系列： | * |
DS2401
1-Wire SIGNALING
The DS2401 requires a strict protocol to ensure data integrity. The protocol consists of four types of
signaling on one line: reset sequence with Reset Pulse and Presence Pulse, write 0, write 1, and read data.
All these signals except Presence Pulse are initiated by the bus master.
The initialization sequence required to begin any communication with the DS2401 is shown in Figure 5.
A reset pulse followed by a Presence Pulse indicates the DS2401 is ready to send or receive data given
the correct ROM command.
The bus master transmits (TX ) a reset pulse (tRSTL , minimum 480s). The bus master then releases the
line and goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the 5k pullup resistor.
After detecting the rising edge on the data pin, the DS2401 waits (tPDH, 15-60s) and then transmits the
Presence Pulse (tPDL, 60-240s). The 1-Wire bus requires a pullup resistor range of 1.5k to 5k,
depending on bus load characteristics.
READ/WRITE TIME SLOTS
The definitions of write and read time slots are illustrated in Figure 6. All time slots are initiated by the
master driving the data line low. The falling edge of the data line synchronizes the DS2401 to the master
by triggering a delay circuit in the DS2401. During write time slots, the delay circuit determines when the
DS2401 will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit
determines how long the DS2401 will hold the data line low overriding the “1” generated by the master.
If the data bit is a 1, the DS2401 will leave the read data time slot unchanged.
相关PDF资料 |
PDF描述 |
|---|---|
| DSPIC33FJ128MC710-I/PF | IC DSPIC MCU/DSP 128K 100TQFP |
| VI-BTT-IW-F2 | CONVERTER MOD DC/DC 6.5V 100W |
| PIC24FJ128DA210-I/BG | MCU PIC 16BIT FLASH 128K 121BGA |
| D38999/20MD97PN | CONN RCPT 12POS WALL MNT W/PINS |
| MS27468T17B99S | CONN RCPT 23POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2401X1-T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Silicon Serial Number Unique, Factory-Lasered and Tested 64-Bit |
| DS2401Y | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Silicon Serial Number |
| DS2401Z | 制造商:Maxim Integrated Products 功能描述:SER#, ST223 (GENERIC) - Rail/Tube 制造商:Maxim Integrated Products 功能描述:SILICON SERIAL NUMBER SMD 2401 |
| DS2401Z/T&R | 制造商:Maxim Integrated Products 功能描述:SER#, ST223-TRL (GENERIC) - Tape and Reel |
| DS2401Z+ | 功能描述:序列号注册 Silicon Serial Number RoHS:否 制造商:Maxim Integrated 数据总线宽度: 电源电压-最大: 电源电压-最小: 最大工作温度: 最小工作温度: 安装风格: 封装 / 箱体: |
发布紧急采购，3分钟左右您将得到回复。