- 您现在的位置：买卖IC网 > PDF目录1915 > DS2411P+T&R (Maxim Integrated Products)IC SILICON SERIAL NUMBER 6TSOC PDF资料下载
参数资料
| 型号： | DS2411P+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/12页 |
| 文件大小： | 0K |
| 描述： | IC SILICON SERIAL NUMBER 6TSOC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 4,000 |
| 类型： | 硅序列号 |
| 应用： | PCB，网络节点，设备识别/注册 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-LSOJ |
| 供应商设备封装： | 6-TSOC |
| 包装： | 带卷 (TR) |
DS2411
8 of 12
1-WIRE SIGNALING
The DS2411 requires strict protocols to ensure data integrity. The protocol consists of four types of
signaling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1, and Read
Data. Except for the presence pulse the bus master initiates all these signals. The DS2411 can
communicate at two different speeds: standard speed and Overdrive speed. If not explicitly set into the
Overdrive mode, the DS2411 will communicate at standard speed. While in Overdrive Mode the fast
timing applies to all waveforms.
To get from idle to active, the voltage on the 1-Wire line needs to fall from VPUP below the threshold VTL.
To get from active to idle, the voltage needs to rise from VILMAX past the threshold VTH. The voltage
VILMAX is relevant for the DS2411 when determining a logical level, but not for triggering any events.
The initialization sequence required to begin any communication with the DS2411 is shown in Figure 6.
A Reset Pulse followed by a Presence Pulse indicates the DS2411 is ready to receive data, given the
correct ROM and memory function command. In a mixed population network, the reset low time tRSTL
needs to be long enough for the slowest 1-Wire slave device to recognize it as a reset pulse. If the bus
master uses slew-rate control on the falling edge, it must pull down the line for tRSTL + tF to compensate
for the edge. A tRSTL duration of 480s or longer will exit the Overdrive Mode returning the device to
standard speed. If the DS2411 is in Overdrive Mode and tRSTL is no longer than 80s, the device will
remain in Overdrive Mode.
After the bus master has released the line it goes into receive mode (RX). Now, the 1-Wire bus is pulled
to VPUP via the pullup resistor or, in case of a DS2480B driver, by active circuitry. When the threshold
VTH is crossed, the DS2411 waits for tPDH and then transmits a Presence Pulse by pulling the line low for
tPDL. To detect a presence pulse, the master must test the logical state of the 1-Wire line at tMSP.
The tRSTH window must be at least the sum of tPDHMAX, tPDLMAX, and tRECMIN. Immediately after tRSTH is
expired, the DS2411 is ready for data communication. In a mixed population network, tRSTH should be
extended to minimum 480s at standard speed and 48s at Overdrive speed to accommodate other 1-
Wire devices.
Read/Write Time Slots
Data communication with the DS2411 takes place in time slots that carry a single bit each. Write time
slots transport data from bus master to slave. Read time-slots transfer data from slave to master. The
definitions of the write and read time slots are illustrated in Figure 7.
All communication begins with the master pulling the data line low. As the voltage on the 1-Wire line
falls below the threshold VTL, the DS2411 starts its internal timing generator that determines when the
data line will be sampled during a write time slot and how long data will be valid during a read time slot.
Master to Slave
For a write-one time slot, the voltage on the data line must have crossed the VTHMAX threshold after the
write-one low time tW1LMAX is expired. For a write-zero time slot, the voltage on the data line must stay
below the VTHMIN threshold until the write-zero low time tW0LMIN is expired. For most reliable
communication the voltage on the data line should not exceed VILMAX during the entire tW0L window.
After the VTHMAX threshold has been crossed, the DS2411 needs a recovery time tREC before it is ready for
the next time slot.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2413Q+T&R | IC SWITCH 2CH ADDRESS 6-TDFN |
| DS2480B+ | IC LINE DRVR W/SENSOR 1-W 8-SOIC |
| DS2482X-100+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2482X-101+T | IC MASTER I2C-1WIRE 1CH 9-WLP |
| DS2483Q+T | IC I2C TO 1WIRE BRIDGE 8TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2411R/R | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Silicon Serial Number with VCC Input |
| DS2411R/T | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Silicon Serial Number with VCC Input |
| DS2411R/T&R | 制造商:Maxim Integrated Products 功能描述:SILICON SER# W/VCC INPUT, SOT23 T&R - Tape and Reel 制造商:Rochester Electronics LLC 功能描述: |
| DS2411R/T&R | 功能描述:序列号注册 RoHS:否 制造商:Maxim Integrated 数据总线宽度: 电源电压-最大: 电源电压-最小: 最大工作温度: 最小工作温度: 安装风格: 封装 / 箱体: |
| DS2411R+-LF | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。