- 您现在的位置：买卖IC网 > PDF目录9413 > DS2417P+ (Maxim Integrated Products)IC TIMECHIP W/INTRPT 1WIRE 6TSOC PDF资料下载
参数资料
| 型号： | DS2417P+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 2/15页 |
| 文件大小： | 0K |
| 描述： | IC TIMECHIP W/INTRPT 1WIRE 6TSOC |
| 产品培训模块： | 1-Wire Communications Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 120 |
| 类型： | 二进制计数器 |
| 特点： | 唯一 ID |
| 时间格式： | 二进制 |
| 数据格式： | 二进制 |
| 接口： | 1 线 串行 |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 6-LSOJ |
| 供应商设备封装： | 6-TSOC |
| 包装： | 管件 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
DS2417
1–WIRE SIGNALING
The DS2417 requires strict protocols to ensure data integrity. The protocol consists of four types of sig-
naling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1, and Read
Data. Except for the presence pulse the bus master initiates all these signals.
The initialization sequence required to begin any communication with the DS2417 is shown in Figure 8.
A reset pulse followed by a presence pulse indicates the DS2417 is ready to send or receive data. The bus
master transmits (TX) a reset pulse (tRSTL, minimum 480s). The bus master then releases the line and
goes into receive mode (RX). The 1-Wire bus is pulled to a high state via the pullup resistor. After
detecting the rising edge on the data line, the DS2417 waits (tPDH, 15μs to 60μs) and then transmits the
presence pulse (tPDL, 60μs to 240μs).
INITIALIZATION PROCEDURE “RESET AND PRESENCE PULSES” Figure 8
RESISTOR
MASTER
DS2417
MASTER RX "PRESENCE PULSE"
480 s tRSTL < *
480 s tRSTH < **
15 s tPDH < 60 s
60 tPDL < 240 s
MASTER TX
"RESET PULSE"
VPULLUP
PULLUP MIN
VIH MIN
VIL MAX
0V
tRSTH
tRSTL
tPDH
tPDL
tR
V
*
In order not to mask interrupt signaling by other devices on the 1-Wire bus tRSTL + tR should al-
ways be less than 960s.
**
Includes recovery time
READ/WRITE TIME SLOTS
The definitions of write and read time slots are illustrated in Figure 9. The master initiates all time slots
by driving the data line low. The falling edge of the data line synchronizes the DS2417 to the master by
triggering an internal delay circuit. During write time slots, the delay circuit determines when the
DS2417 will sample the data line. For a read data time slot, if a “0” is to be transmitted, the delay circuit
determines how long the DS2417 will hold the data line low. If the data bit is a “1”, the DS2417 will not
hold the data line low at all.
10 of 15
相关PDF资料 |
PDF描述 |
|---|---|
| DS1344E-18+T&R | IC RTC SPI 1.8V 20TSSOP |
| VI-22K-MX-B1 | CONVERTER MOD DC/DC 40V 75W |
| VI-22K-MW | CONVERTER MOD DC/DC 40V 100W |
| VI-22J-MX-B1 | CONVERTER MOD DC/DC 36V 75W |
| MS27473E22F35PC | CONN PLUG 100POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2417P/T&R | 制造商:Maxim Integrated Products 功能描述:IC TIMECHIP W/INTRPT 1WIRE 6TSOC |
| DS2417P/T&R | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS2417P+ | 功能描述:实时时钟 1-Wire w/Interrupt RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| DS2417P+T&R | 制造商:Maxim Integrated Products 功能描述:REAL TIME CLOCK SERL 6PIN TSOC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TIMECHIP W/INTRPT 1WIRE 6TSOC 制造商:Maxim Integrated Products 功能描述:Real Time Clock 1-Wire w/Interrupt |
| DS2417P+T&R | 功能描述:实时时钟 1-Wire w/Interrupt RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。