- 您现在的位置：买卖IC网 > PDF目录17135 > DS2438Z (Maxim Integrated Products)IC MONITOR SMART BATTERY 8-SOIC PDF资料下载
参数资料
| 型号： | DS2438Z |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/29页 |
| 文件大小： | 0K |
| 描述： | IC MONITOR SMART BATTERY 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 智能电池 |
| 电源电压： | 2.4 V ~ 10 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
DS2438
1-Wire BUS SYSTEM
The 1-Wire bus is a system which has a single bus master and one or more slaves. The DS2438 behaves
as a slave. The discussion of this bus system is broken down into three topics: hardware configuration,
transaction sequence, and 1-Wire signaling (signal types and timing).
HARDWARE CONFIGURATION
The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to
drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have open
drain or 3-state outputs. The 1-Wire port of the DS2438 (DQ pin) is open drain with an internal circuit
equivalent to that shown in Figure 8. A multidrop bus consists of a 1-Wire bus with multiple slaves
attached. The 1-Wire bus requires a pull-up resistor of approximately 5 k W .
HARDWARE CONFIGURATION Figure 8
The idle state for the 1 wire bus is high. If for any reason a transaction needs to be suspended, the bus
MUST be left in the idle state if the transaction is to resume. Infinite recovery time can occur between
bits so long as the 1-Wire bus is in the inactive (high) state during the recovery period. If this does not
occur and the bus is left low, all components on the bus will be reset. See Wire-1 Reset Pulse Timing
(Figure 9).
TRANSACTION SEQUENCE
The protocol for accessing the DS2438 via the 1-Wire port is as follows:
§
§
§
§
Initialization
ROM Function Command
Memory Function Command
Transaction/Data
INITIALIZATION
All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence
consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the
slave(s). The presence pulse lets the bus master know that the DS2438 is on the bus and is ready to
operate. For more details, see the “1-Wire Signaling” section.
17 of 29
相关PDF资料 |
PDF描述 |
|---|---|
| VI-JW4-EZ | CONVERTER MOD DC/DC 48V 25W |
| EEC13DRTS-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| SI85XX-EVB | BOARD EVAL CURRENT SENSOR 10A |
| GBC25DRYN-S13 | CONN EDGECARD 50POS .100 EXTEND |
| NC-508095-5-9 | LABEL ID PRODUCT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2438Z/T&R | 制造商:Maxim Integrated Products 功能描述:SMART BATTERY MONITOR 8-SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 8-SOIC |
| DS2438Z/T&R | 功能描述:IC MONITOR SMART BATTERY 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| DS2438Z+ | 功能描述:电池管理 Smart Battery Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2438Z+T&R | 制造商:Maxim Integrated Products 功能描述:MONITOR MULTI-CHEM 8SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:BATT MONITOR 8-SOIC T&R PBFREE 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 8-SOIC 制造商:Maxim Integrated Products 功能描述:Battery Management Smart Battery Monitor |
| DS2438Z+T&R | 功能描述:电池管理 Smart Battery Monitor RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。