- 您现在的位置：买卖IC网 > PDF目录11711 > DS2490S (Maxim Integrated Products)IC BRIDGE CLIP USB TO 1-W 24SOIC PDF资料下载
参数资料
| 型号： | DS2490S |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/50页 |
| 文件大小： | 0K |
| 描述： | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| 标准包装： | 31 |
| 应用： | USB |
| 接口： | 1 线 |
| 电源电压： | 3 V ~ 5.5 V |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
DS2490
30 of 50
Description
Offset
Data
Write-1 Low Time
0x05
current Write-1 low time code
Data Sample Offset /
Write-0 Recovery Time
0x06
current data sample offset/ Write-0 recovery time code
Reserved (Test Register)
0x07
Device Status Flags
0x08
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
EP0F
--
IDLE
HALT
PMOD
--
SPUA
Bit Definitions:
SPUA if set to 1, the strong pullup to 5V is currently active, if
set to 0, it is inactive.
bit 1: Reserved
bit 2: Reserved
PMOD if set to 1, the DS2490 is powered from USB and
external sources, if set to 0, all DS2490 power is
provided from USB.
HALT if set to 1, the DS2490 is currently halted, if set to 0, the
device is not halted.
IDLE if set to 1, the DS2490 is currently idle, if set to 0, the
device is not idle.
bit 6: Reserved
EPOF: Endpoint 0 FIFO status, see Note 1.
Communication
Command, Byte 1
0x09
Communication command currently being processed. If the device
is idle, a register value of 0x00 is sent.
Communication
Command, Byte 2
0x0A
Communication command currently being processed. If the device
is idle, a register value of 0x00 is sent.
Communication
Command Buffer Status
0x0B
Number of data bytes currently contained in the 16-byte FIFO used
to hold communication commands.
1-Wire Data Out Buffer
Status
0x0C
Number of data bytes currently contained in the 128-byte FIFO
used to write data to the 1-Wire bus.
1-Wire Data In Buffer
Status
0x0D
Number of data bytes currently contained in the 128-byte command
FIFO used to read data from the 1-Wire bus.
Reserved (Test Register)
0x0E
Reserved
Reserved (Test Register)
0x0F
Reserved
Notes:
1. If EP0F is set to 1, the Endpoint 0 FIFO was full when a new control transfer setup packet was
received. This is an error condition in that the setup packet received is discarded due to the full
condition. To recover from this state the USB host must send a CTL_RESET_DEVICE command; the
device will also recover with a power on reset cycle. Note that the DS2490 will accept and process a
CTL_RESET_DEVICE command if the EP0F = 1 state occurs. If EP0F = 0, no FIFO error condition
exists.
相关PDF资料 |
PDF描述 |
|---|---|
| V24B5H150BL2 | CONVERTER MOD DC/DC 5V 150W |
| D38999/26JD5PA | CONN PLUG 5POS STRAIGHT W/PINS |
| V24B5H150BF3 | CONVERTER MOD DC/DC 5V 150W |
| V24B5H150B2 | CONVERTER MOD DC/DC 5V 150W |
| V24B48H150BL3 | CONVERTER MOD DC/DC 48V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2490S+ | 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Rail/Tube 制造商:Maxim Integrated Products 功能描述:USB 1-W BRIDGE CHIP 24-SO LF 制造商:Maxim Integrated Products 功能描述:Bulk |
| DS2490S+T&R | 制造商:Maxim Integrated Products 功能描述:USB TO 1-WIRE BRIDGE 24SOIC W - Tape and Reel |
| DS2490S+TR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:USB to 1-Wire Bridge Chip |
| DS2490X | 制造商:未知厂家 制造商全称:未知厂家 功能描述:USB to 1-Wire Bridge Chip(468.41 k) |
| DS2490X/T&R | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
发布紧急采购，3分钟左右您将得到回复。