- 您现在的位置：买卖IC网 > PDF目录9756 > DS26303L-75+A3 (Maxim Integrated Products)IC LIU E1/T1/J1 3.3V 144-ELQFP PDF资料下载
参数资料
| 型号： | DS26303L-75+A3 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 68/101页 |
| 文件大小： | 0K |
| 描述： | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 8/8 |
| 规程： | T1/E1/J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP 裸露焊盘 |
| 供应商设备封装： | 144-LQFP 裸露焊盘 |
| 包装： | 托盘 |
| 其它名称： | 90-26303+7A3 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页当前第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页
DS26303: 3.3V, T1/E1/J1, Short-Haul, Octal Line Interface Unit
69 of 101
After configuring these bits, the pattern must be loaded into the BERT. This is accomplished through a 0-to-1
Monitoring the BERT requires reading the BSR register that contains the BEC bit and the OOS bit. The BEC bit is 1
when the bit-error counter is 1 or more. The OOS is 1 when the receive pattern generator is not synchronized to
the incoming pattern, which will occur when it receives a minimum 6 bit errors within a 64-bit window. The receive
BERT bit-count register (RBCR) and the receive BERT bit-error count register (RBECR) are updated upon the
reception of a performance-monitor update signal (e.g., BCR.LPMU). This signal updates the registers with the
values of the counters since the last update and resets the counters.
6.9.2
BERT Interrupt Handling
There are four BERT events that can potentially trigger an interrupt. A performance monitoring update, a bit error, a
non-zero bit error count, or an Out Of Synchronization (OOS). The interrupt functions as follows:
When a status bit (BSR:PMS, BEC, or OOS) changes on an interruptible event, the corresponding interrupt
status bit (BSRL.PMSL BEL, BECL, or OOSL) is set. The
INTB pin will go low if the event is enabled through
the corresponding interrupt-enable bit (BSRIE.PMSIE BEIE, BECIE, or OOSIE).
When an interrupt occurs, the host processor must read the interrupt status register (BSRL) to determine the
source of the interrupt. If the interrupt status registers are set for clear-on-read (GISC.CWE reset), the read
also clears the Interrupt Status register which clears the output
INTB pin. If the interrupt status registers are set
for (GISC.CWE set), a 1 must be written to the interrupt status bit (BSRL.PMSL BEL, BECL, or OOSL) in order
to clear it which clears the output
INTB pin.
Subsequently, the host processor can read the status register (BSR) to check the real-time status of the event.
6.9.3
Receive Pattern Detection
The receive BERT receives only the payload data and synchronizes the receive pattern generator to the incoming
pattern. The receive pattern generator is a 32-bit shift register that shifts data from the least significant bit (LSB) or
bit 1 to the most significant bit (MSB) or bit 32. The input to bit 1 is the feedback. For a PRBS pattern (generating
polynomial x
n + xy + 1), the feedback is an XOR of bit n and bit y. For a repetitive pattern (length n), the feedback is
bit n. The values for n and y are individually programmable (1 to 32). The output of the receive pattern generator is
the feedback. If QRSS is enabled, the feedback is an XOR of bits 17 and 20, and the output is forced to 1 if the
next 14 bits are all 0s. QRSS is programmable (on or off). For PRBS and QRSS patterns, the feedback is forced to
1 if bits 1 through 31 are all 0s. Depending on the type of pattern programmed, pattern detection performs either
PRBS synchronization or repetitive pattern synchronization.
6.9.3.1
Receive PRBS Synchronization
PRBS synchronization synchronizes the receive pattern generator to the incoming PRBS or QRSS pattern. The
receive pattern generator is synchronized by loading 32 data stream bits into the receive pattern generator, and
then checking the next 32 data stream bits. Synchronization is achieved if all 32 bits match the incoming pattern. If
at least six incoming bits in the current 64-bit window do not match the receive pattern generator, automatic pattern
re-synchronization is initiated. Automatic pattern resynchronization can be disabled.
See Figure 6-12 for the PRBS synchronization diagram.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27474E14B15P | CONN RCPT 15POS JAM NUT W/PINS |
| D38999/26FH55PA | CONN PLUG 55POS STRAIGHT W/PINS |
| MS27473T20F41PA | CONN PLUG 41POS STRAIGHT W/PINS |
| VI-24J-MX-F1 | CONVERTER MOD DC/DC 36V 75W |
| HI5812JIBZ | ADC 12BIT 50KSPS 1.5LSB 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS26303LN-120 | 功能描述:电信线路管理 IC RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| DS26303LN-120+ | 功能描述:电信线路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| DS26303LN-120+A3 | 功能描述:电信线路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| DS26303LN-120A3 | 功能描述:电信线路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| DS26303LN-75 | 功能描述:电信线路管理 IC 3.3V E1/T1/J1 Short Haul Octal LIU RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。