- 您现在的位置：买卖IC网 > PDF目录378591 > DS2703 SHA-1 Battery Pack Authentication IC PDF资料下载
参数资料
| 型号： | DS2703 |
| 英文描述： | SHA-1 Battery Pack Authentication IC |
| 中文描述： | SHA-1电池组鉴定IC |
| 文件页数： | 12/20页 |
| 文件大小： | 238K |
| 代理商： | DS2703 |
DS2703 SHA-1 Battery Pack Authentication IC
12 of 20
NET ADDRESS COMMANDS
Once the bus master has detected the presence of one or more slaves, it can issue one of the net address
commands described in the following paragraphs. The name of each Net Address command (ROM command) is
followed by the 8-bit opcode for that command in square brackets. Figure 6 presents a transaction flowchart of the
net address commands.
Read Net Address [33h].
This command allows the bus master to read the DS2703’s 1-Wire net address. This
command can only be used if there is a single slave on the bus. If more than one slave is present, a data collision
occurs when all slaves try to transmit at the same time (open drain produces a wired-AND result).
Match Net Address [55h].
This command allows the bus master to specifically address one DS2703 on the 1-Wire
bus. Only the addressed DS2703 responds to any subsequent function command. All other slave devices ignore
the function command and wait for a reset pulse. This command can be used with one or more slave devices on
the bus.
Skip Net Address [CCh].
This command saves time when there is only one DS2703 on the bus by allowing the
bus master to issue a function command without specifying the address of the slave. If more than one slave device
is present on the bus, a subsequent function command can cause a data collision when all slaves transmit data at
the same time.
Search Net Address [F0h].
This command allows the bus master to use a process of elimination to identify the
1-Wire net addresses of all slave devices on the bus. The search process involves the repetition of a simple three-
step routine: read a bit, read the complement of the bit, then write the desired value of that bit. The bus master
performs this simple three-step routine on each bit location of the net address. After one complete pass through all
64 bits, the bus master knows the address of one device. The remaining devices can then be identified on
additional iterations of the process. See Chapter 5 of the
Book of DS19xx iButton
Standards
for a comprehensive
discussion of a net address search, including an actual example (www.maxim-ic.com/iButtonBook).
iButton is a registered trademark of Dallas Semiconductor.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2703U | SHA-1 Battery Pack Authentication IC |
| DS2703UR | SHA-1 Battery Pack Authentication IC |
| DS2703UT | SHA-1 Battery Pack Authentication IC |
| DS2715 | NiMH Battery Pack Charge Controller |
| DS2715Z | NiMH Battery Pack Charge Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2703EVKIT+ | 制造商:Maxim Integrated Products 功能描述:SS CLK GEN 8-64MHZ 8-USOP TRL LF - Boxed Product (Development Kits) |
| DS2703G+T&R | 制造商:Maxim Integrated Products 功能描述:BATT PACK ID W/SHA-1 TDFN-8 T&R LF - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC BATT AUTHENTICAT SHA-1 8-TDFN |
| DS2703G+T&R | 功能描述:电池管理 SHA-1 Battery Pack Authentication RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2703G-C1+T&R | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2703G-CE+T&R | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。