参数资料
型号: DS2703G+T&R
厂商: Maxim Integrated Products
文件页数: 14/20页
文件大小: 0K
描述: IC BATT AUTHENTICAT SHA-1 8-TDFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 10,000
功能: 电池验证
电池化学: 锂离子(Li-Ion)
电源电压: 2.7 V ~ 5.5 V
工作温度: -20°C ~ 70°C
安装类型: 表面贴装
封装/外壳: 8-TDFN
供应商设备封装: 8-TDFN-EP(2x3)
包装: 带卷 (TR)
DS2703 SHA-1 Battery Pack Authentication IC
I/O SIGNALING
The 1-Wire bus requires strict signaling protocols to ensure data integrity. The four protocols used by the DS2703
are as follows: the initialization sequence (reset pulse followed by presence pulse), write 0, write 1, and read data.
The bus master initiates all these types of signaling except the presence pulse.
The initialization sequence required to begin any communication with the DS2703 is shown in Figure 7. A presence
pulse following a reset pulse indicates that the DS2703 is ready to accept a net address command. The bus master
transmits (Tx) a reset pulse for t RSTL . The bus master then releases the line and goes into receive mode (Rx). The
1-Wire bus line is then pulled high by the pullup resistor. After detecting the rising edge on the DQ pin, the DS2703
waits for t PDH and then transmits the presence pulse for t PDL .
Figure 7. 1-Wire Initialization Sequence
t RSTL
t PDH
t PDL
t RSTH
V PULLUP
DQ
GND-
LINE TYPE LEGEND:
BUS MASTER ACTIVE LOW
BOTH BUS MASTER AND
DS2703 ACTIVE LOW
RESISTOR PULLUP
DS2703 ACTIVE LOW
WRITE-TIME SLOTS
A write-time slot is initiated when the bus master pulls the 1-Wire bus from a logic-high (inactive) level to a logic-low
level. There are two types of write-time slots: write 1 and write 0. All write-time slots must be t SLOT in duration with
a 1 μ s minimum recovery time, t REC , between cycles. The DS2703 samples the 1-Wire bus line between t LOW1_MAX
and t LOW0_MIN after the line falls. If the line is high when sampled, a write 1 occurs. If the line is low when sampled, a
write 0 occurs. The sample window is illustrated in Figure 8. 1-Wire Write and Read Time Slots. For the bus master
to generate a write 1 time slot, the bus line must be pulled low and then released, allowing the line to be pulled high
less than t RDV after the start of the write time slot. For the host to generate a write 0 time slot, the bus line must be
pulled low and held low for the duration of the write-time slot.
Caution : When communicating in standard mode, the number of consecutive Write 0 time slots with t LOW0 =
t LOW0_MAX and t REC = t REC_MIN is limited to 64. If more than 64 Write 0 time slots with t LOW0 = t LOW0_MAX and t REC =
t REC_MIN are issued, the internal supply (V DD_INT ) can drop so low that the DS2703 resets. Increasing t REC to 5 μ s
allows Vdd_int to recharge sufficiently each time slot.
READ-TIME SLOTS
A read-time slot is initiated when the bus master pulls the 1-Wire bus line from a logic-high level to a logic-low level.
The bus master must keep the bus line low for at least 1 μ s and then release it to allow the DS2703 to present valid
data. The bus master can then sample the data t RDV from the start of the read-time slot. By the end of the read-
time slot, the DS2703 releases the bus line and allows it to be pulled high by the external pullup resistor. All read-
time slots must be t SLOT in duration with a 1 μ s minimum recovery time, t REC , between cycles. See Figure 8 and the
timing specifications in the Electrical Characteristics table for more information.
14 of 20
相关PDF资料
PDF描述
VE-B1V-EY-F1 CONVERTER MOD DC/DC 5.8V 50W
ECC28DJCN-S1136 CONN EDGECARD 56PS .100 PRESSFIT
M3TKK-6060K IDC CABLE - MSD60K/MC60F/MPK60K
RP15-2412SFW/N CONV DC/DC 15W 9-36VIN 12VOUT
VI-B1V-EY-F4 CONVERTER MOD DC/DC 5.8V 50W
相关代理商/技术参数
参数描述
DS2703K 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2703U 制造商:Maxim Integrated Products 功能描述:BATT PACK ID W/SHA-1 8PIN USOP - Rail/Tube
DS2703U/T&R 制造商:Maxim Integrated Products 功能描述:BATT PACK ID W/SHA-1 8PIN USOP T&R - Tape and Reel
DS2703U+ 功能描述:电池管理 SHA-1 Battery Pack Authentication RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2703U+R 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:SHA-1 Battery Pack Authentication IC