- 您现在的位置：买卖IC网 > PDF目录17128 > DS2711E+T&R (Maxim Integrated Products)IC NIMH CHARGER 16TSSOP PDF资料下载
参数资料
| 型号： | DS2711E+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 12/15页 |
| 文件大小： | 0K |
| 描述： | IC NIMH CHARGER 16TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 功能： | 充电管理 |
| 电池化学： | 镍金属氢化物 |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
DS2711/DS2712: Loose-Cell NiMH Chargers
Table 2. Charge Mode Selection
LED2 PIN STRAPPING
Low
Open
High
MODE
1-Cell Series
2-Cell Series
Parallel
CC1 and CC2 Outputs
The CC1 and CC2 operate as open-drain outputs that drive active low to connect the charge source to the battery
cell. During charge, the behavior of the CC1 and CC2 outputs depends on the charge-mode configuration. In
parallel mode, CC1 and CC2 are driven low in alternating time slots. The charge source is loaded by just one cell
during any time slot. In the 1-cell and 2-cell series mode, only CC1 is driven. Except for the periodic performance of
impedance and - ? V tests, series mode charging is continuous during the fast charge phase rather than pulsed in
parallel mode.
Parallel Mode Fast Charge
Referring to Figure 4, CC1 controls the PNP switch that gates current to the cell in slot 1. CC2 controls the PNP
switch that gates current to the cell in slot 2. During fast charge, current is gated to each slot sequentially, with
charge pulses occurring in alternating time frames. The cell in one slot charges while the other relaxes and the
effective fast-charge current is 48.4% of the magnitude set by the charge-source current limit. The parallel
configuration skips a charge pulse every 32 clock cycles to facilitate independent testing of the open- and closed-
circuit cell voltages (V OFF and V ON , respectively). Since the charge regime of each cell is independent, one cell may
complete a charge phase before the other. The more fully charged cell of a pair inserted at the same time could
terminate fast charge by - ? V, then charge in top-off while the less charged cell continues in fast charge. In the case
of an improper or faulty cell (e.g., alkaline) being inserted along with a proper cell (NiMH or NiCd), charging of the
faulty cell would be stopped, while the proper cell is charged to full.
Series Mode Fast Charge
Referring to Figure 3, CC1 controls the PNP switch that gates current to the cell(s). In series mode, 1 or 2 cells can
be charged, depending on whether the 1-cell or 2-cell series mode has been selected. During fast charge, current
is gated to the cell(s) almost continuously, with the effective fast-charge current approximately equal to current limit
of the charge source. The series configuration deactivates CC1 briefly every 32 clock cycles to facilitate
independent testing of V OFF and V ON of each cell. The one second deactivation makes the duty factor 0.969 and
therefore the effective current equals approximately 97% of the charge-source current limit. In the 2-cell series
mode, the characteristics of each cell are evaluated individually; however charging stops if either cell is determined
to be improper or faulty.
In the 1-cell charge series mode, CC1 gates the charge current as in the 2-cell series mode. The cell voltage is
monitored between VP1 and VN1, and temperature is monitored with THM1. The VP2 and THM2 pins can be left
disconnected in the 1-cell series mode.
EXAMPLE CAPACITIES AND CHARGE RATES
Parallel Charging Example
A 1700mAH cell is charged using a 1A regulated charge source. During fast charge, the cell is charged at a duty
factor of 0.484 and receives an effective charge current of 0.484A. In terms of C-rate, this is 484mA/1700mAh =
0.285 ° C (or C/3.5). During precharge and top-off, the duty factor is 0.125 (i.e., 1/8), for an effective average current
of 125mA, corresponding to a C-rate of 125/1700 = 0.073C (or C/13.6). Similarly, in maintenance mode, the duty
factor is 0.0156 (i.e., 1/64) and the C-rate is 15.6/1700 = 0.0092 ( or C/109). The C-rates for charging 3 different
cell capacities using a 500mA and a 1000mA current source are shown in Table 3.
12 of 15
相关PDF资料 |
PDF描述 |
|---|---|
| DS2711E+ | IC NIMH CHARGER 16TSSOP |
| VE-J1L-EZ | CONVERTER MOD DC/DC 28V 25W |
| VI-J72-EZ | CONVERTER MOD DC/DC 15V 25W |
| RCM15DSUS | CONN EDGECARD 30POS DIP .156 SLD |
| GCA15DTKT | CONN EDGECARD 30POS DIP .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2711EVKIT+ | 制造商:Maxim Integrated Products 功能描述:DS2711 EVAL KIT - Boxed Product (Development Kits) |
| DS2711G | 制造商:Maxim Integrated Products 功能描述:LOOSE CELL NIMH CHGR TQFN 16PIN - Rail/Tube |
| DS2711K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2711Z | 制造商:Maxim Integrated Products 功能描述:LOOSE CELL NIMH CHARGER SOIC 16PIN - Rail/Tube |
| DS2711Z/T&R | 制造商:Maxim Integrated Products 功能描述:LOOSE CELL NIMH CHARG.SOIC16 PIN TR - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。