- 您现在的位置：买卖IC网 > PDF目录15547 > DS2714E+T&R (Maxim Integrated Products)IC NIMH CHARGER QUAD 20TSSOP PDF资料下载
参数资料
| 型号： | DS2714E+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC NIMH CHARGER QUAD 20TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 镍金属氢化物 |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
DS2714: Quad Loose Cell NiMH Charger
CHARGE TIMER
The Charge Timer monitors the duration of charge in Fast and Top-Off charge phases, and is reset at the
beginning of each phase. The time-out period is set with an external resistor connected from the TMR pin to V SS .
Resistors can be selected to support Fast charge time-out periods of 0.5 to 10 hours and Top-off charge time-out
periods of 0.25 to 5 hours. If the timer expires in Fast charge, the timer count is reset and charging proceeds to the
Top-Off charge phase. The Top-Off time-out period is half of the Fast charge time-out period. When the timer
expires in Top-Off, charging proceeds to the Maintenance phase. The programmed charge time approximately
follows the equation:
t = 1.5 * R / 1000
(time in minutes)
SUSPEND
Suspension of charge activity is possible by floating the TMR pin. All CCx outputs become high-Z and the Charge
Timer stops. The state machine and all timers are reset to their Presence Test conditions.
TEMPERATURE SENSE
Connecting an external 10k ? NTC thermistor between THM1 or THM2 (THMx) and V SS , and a 10k ? bias resistor
between V DD and THMx allows the DS2714 to sense temperature. In order to sense the temperature of the battery
cells, locate the thermistor close to the body of the battery cell. The THM1 thermistor should be placed between
cells 1 and 2, and THM2 thermistor between cells 3 and 4. Alternatively, the thermistors can sense ambient
temperature by locating them away from the cells. THM1 and THM2 can be tied together to sense temperature
using a single thermistor and bias resistor. The temperature qualification function can be defeated by tying THMx
pins to a single resistor divider supplying a voltage between the Thermistor-Min and Thermistor-Max threshold
voltages.
MIN, MAX TEMPERATURE COMPARE
The voltage thresholds of the THMx inputs (V THM-MIN , V THM-MAX ) are set to allow Fast charging to start if 0 ° C < T A <
45 ° C when using the recommended 10k ? bias and 10k ? thermistor. If Fast charging is in progress, and the
voltage on THMx reaches V THM-STOP (T A > 50 ° C), Fast charging stops and the maintenance phase begins. In Pre-
charge the device will transition to the Fault state if the voltage on THMx reaches V THM-STOP .
Table 1. THM1, THM2 Thresholds
TEMPERATURE
THM
THRESHOLD
MIN
MAX
STOP
RATIO
OF VDD
0.73
0.33
0.29
THERMISTOR
RESISTANCE
27.04k
4.925k
4.085k
Semitec
103AT-2
0°C
45°C
50°C
Fenwal
197-103LAG-A01
173-103LAF-301
4°C
42°C
47°C
CELL VOLTAGE MONITORING
Individual cell voltages are monitored for minimum and maximum values, using the V BAT-LOW , V BAT-MAX1 and V BAT-
MAX2 threshold limits. Upon inserting a cell or power-up with cells inserted, cell voltages must be less than the V BAT-
MAX1 threshold before charging begins. The V BAT-LOW threshold determines whether a Pre-charge cycle should
precede the Fast charge cycle, and when to transition from Pre-charge to Fast charge. Once Fast charging
commences, cell voltages are compared to the V BAT-MAX2 threshold once every 2 seconds. The comparison occurs
while the charge control pin (CC1-4) controlling current to the cell is active (low). When the charge control pin is
active such that charge is applied to the cell, the cell voltage is referred to as the V ON voltage. When the charge
control pin is inactive, the cell voltage is referred to as the V OFF voltage. Charging is halted and a Fault condition is
displayed if V ON is greater than V BAT-MAX2 . Charging is also halted and a fault condition is entered if V OFF is greater
than V BAT-MAX1 . While Fast charge is in progress, cell voltage measurements are stored and compared to future
measurements for charge termination and cell test purposes.
9 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| GBC13DRTH-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| V24C28T50BF2 | CONVERTER MOD DC/DC 28V 50W |
| 1435864-4 | PATCHCORD CAT6 BLK/BLK BOOT 4' |
| V24C28T50BL3 | CONVERTER MOD DC/DC 28V 50W |
| GSC06DREN-S734 | CONN EDGECARD 12POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2714EVKIT+ | 制造商:Maxim Integrated Products 功能描述:DS2714 EVAL KIT - Boxed Product (Development Kits) |
| DS2714K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2715 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:NiMH Battery Pack Charge Controller |
| DS2715BZ+ | 功能描述:电池管理 NiMH Battery Pack Charge Controller RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2715BZ+T&R | 制造商:Maxim Integrated Products 功能描述:NIMH BATPCK CHGCONT 16PIN SOIC TR L - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CTRLR CHRG NIMH BATT 16-SOIC 制造商:Maxim Integrated Products 功能描述:Battery Management NiMH Battery Pack Charge Controller |
发布紧急采购，3分钟左右您将得到回复。