参数资料
型号: DS2760BE+025
厂商: Maxim Integrated Products
文件页数: 6/25页
文件大小: 0K
描述: IC BATT MON LI-ION HP 16-TSSOP
标准包装: 96
功能: 电池监控器
电池化学: 锂离子(Li-Ion)
电源电压: 2.5 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 16-TSSOP
包装: 管件
DS2760
POWER MODES
The DS2760 has two power modes: Active and Sleep. While in Active Mode, the DS2760 continually
measures current, voltage and temperature to provide data to the host system and to support current
accumulation and Li+ safety monitoring. In Sleep Mode, the DS2760 ceases these activities. The
DS2760 enters Sleep Mode when any of the following conditions occurs:
§ the PMOD bit in the Status Register has been set to 1 and the DQ line is low for longer than
2 seconds (pack disconnection)
§ the voltage on VIN drops below undervoltage threshold V UV for t UVD (cell depletion)
§ the pack is disabled through the issuance of a SWAP command (SWEN bit =1)
The DS2760 returns to Active Mode when any of the following occurs:
§ the PMOD bit has been set to 1 and the SWEN bit is set to 0 and the DQ line is pulled high
(pack connection)
§
§
§
the PS pin is pulled low (power switch)
the voltage on PLS becomes greater than the voltage on VIN (charger connection) with the SWEN bit
set to 0
the pack is enabled through the issuance of a SWAP command (SWEN bit =1)
The DS2760 defaults to Sleep Mode when power is first applied.
LI+ PROTECTION CIRCUITRY
During Active Mode, the DS2760 constantly monitors cell voltage and current to protect the battery from
overcharge (overvoltage), overdischarge (undervoltage) and excessive charge and discharge currents
(overcurrent, short circuit). Conditions and DS2760 responses are described in the sections below and
summarized in Table 2 and Figure 3.
LI+ PROTECTION CONDITIONS AND DS2760 RESPONSES Table 2
Condition
Name
Activation
Threshold Delay Response
Release
Threshold
Overcurrent, Charge V IS > V OC
Overvoltage VIN > V OV
Undervoltage VIN < V UV
(2)
Overcurrent, Discharge V IS < -V OC(2)
Short Circuit V SNS > V SC
t OVD
t UVD
t OCD
t OCD
t SCD
CC high
CC , DC high,
Sleep Mode
CC , DC high
DC high
DC high
VIN < V CE
V PLS > V DD(1)
(charger connected)
V PLS < V DD – V TP(3)
V PLS > V DD – V TP(4)
V PLS > V DD – V TP(4)
V IS = V IS1 – V IS2 . Logic high = V PLS for CC and V DD for DC . All voltages are with respect to VSS. I SNS
references current delivered from pin SNS.
(1) If V DD <2.2V, release is delayed until the recovery charge current (I RC ) passed from PLS to V DD
charges the battery and allows V DD to exceed 2.2V.
(2) for the internal sense resistor configuration, the overcurrent thresholds are expressed in terms of
current: I SNS > I OC for charge direction and I SNS < -I OC for discharge direction
(3) with test current I TST current flowing from PLS to VSS (pull-down on PLS)
(4) with test current I TST current flowing from V DD to PLS (pull-up on PLS)
Overvoltage. If the voltage of the cell exceeds overvoltage threshold V OV for a period longer than
overvoltage delay t OVD , the DS2760 shuts off the external charge FET and sets the OV flag in the
Protection Register. When the cell voltage falls below charge enable threshold V CE , the DS2760 turns the
6
相关PDF资料
PDF描述
GCA22DTKH-S288 CONN EDGECARD 44POS .125 EXTEND
MT9P031I12STCD ES KIT DEV FOR MT9P031
DS2761AE+ IC MON BATT LI-ION HP 16-TSSOP
AS5043 DB V2 BOARD DEMO AS5043
38H202C INDUCTOR 2.00UH 6.5A SMD
相关代理商/技术参数
参数描述
DS2760BE-025/T&R 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC BATT MON LI-ION HP 16-TSSOP
DS2760BE-025/T&R 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2760BX 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:High-Precision Li Battery Monitor
DS2760BX-025 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:High-Precision Li Battery Monitor
DS2760BX-025/T&R 制造商:Maxim Integrated Products 功能描述:IC BATT MON LI-ION HP FLIPCHIP