参数资料
型号: DS2761AE
厂商: Maxim Integrated Products
文件页数: 20/24页
文件大小: 0K
描述: IC MON BATT LI-ION HP 16-TSSOP
标准包装: 96
功能: 电池监控器
电池化学: 锂离子(Li-Ion)
电源电压: 2.5 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 16-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 16-TSSOP
包装: 管件
DS2761
I/O SIGNALING
The 1-Wire bus requires strict signaling protocols to insure data integrity. The four protocols used by the
DS2761 are as follows: the initialization sequence (reset pulse followed by presence pulse), write 0, write
1, and read data. All of these types of signaling except the presence pulse are initiated by the bus master.
The initialization sequence required to begin any communication with the DS2761 is shown in Figure 17.
A presence pulse following a reset pulse indicates that the DS2761 is ready to accept a net address
command. The bus master transmits (Tx) a reset pulse for t RSTL . The bus master then releases the line and
goes into receive mode (Rx). The 1-Wire bus line is then pulled high by the pullup resistor. After
detecting the rising edge on the DQ pin, the DS2761 waits for t PDH and then transmits the presence pulse
for t PDL .
Figure 17. 1-WIRE INITIALIZATION SEQUENCE
t RSTL
t PDH
t PDL
t RSTH
PACK+
DQ
PACK-
LINE TYPE LEGEND:
BUS MASTER ACTIVE LOW
BOTH BUS MASTER AND
DS2761 ACTIVE LOW
RESISTOR PULLUP
DS2761 ACTIVE LOW
WRITE-TIME SLOTS
A write-time slot is initiated when the bus master pulls the 1-Wire bus from a logic-high (inactive) level
to a logic-low level. There are two types of write-time slots: write 1 and write 0. All write-time slots must
be t SLOT (60 m s to 120 m s) in duration with a 1 m s minimum recovery time, t REC , between cycles. The
DS2761 samples the 1-Wire bus line between 15 m s and 60 m s after the line falls. If the line is high when
sampled, a write 1 occurs. If the line is low when sampled, a write 0 occurs (see Figure 18). For the bus
master to generate a write 1 time slot, the bus line must be pulled low and then released, allowing the line
to be pulled high within 15 m s after the start of the write time slot. For the host to generate a write 0 time
slot, the bus line must be pulled low and held low for the duration of the write-time slot.
READ-TIME SLOTS
A read-time slot is initiated when the bus master pulls the 1-Wire bus line from a logic-high level to a
logic-low level. The bus master must keep the bus line low for at least 1 m s and then release it to allow the
DS2761 to present valid data. The bus master can then sample the data t RDV (15 m s) from the start of the
read-time slot. By the end of the read-time slot, the DS2761 releases the bus line and allows it to be
pulled high by the external pullup resistor. All read-time slots must be t SLOT (60 m s to 120 m s) in duration
with a 1 m s minimum recovery time, t REC , between cycles. See Figure 18 for more information.
20 of 24
相关PDF资料
PDF描述
HT-SCE-1K-3/16-2.0-9 HEAT SHRINK SLEEVE MARKER
ECA15DTKT CONN EDGECARD 30POS DIP .125 SLD
ECA18DTAH CONN EDGECARD 36POS R/A .125 SLD
AIRD-01-1R2M INDUCTOR PWR DRUM CORE 1.2UH
L04023R3BHNTR INDUCTOR THIN FILM 3.3NH 0402
相关代理商/技术参数
参数描述
DS2761AE+ 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2761AE+025 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2761AE+025/T&R 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:IC MON BATT LI-ION HP 16-TSSOP
DS2761AE+025/T&R 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel
DS2761AE-025 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel