- 您现在的位置：买卖IC网 > PDF目录15545 > DS2778G+T&R (Maxim Integrated Products)IC FUEL GAUGE LI+ 2CELL 14-TDFN PDF资料下载
参数资料
| 型号： | DS2778G+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 44/46页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE LI+ 2CELL 14-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4 V ~ 9.2 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页
2-Cell, Stand-Alone, Li+ Fuel-Gauge IC with
Protector and Optional SHA-1 Authentication
Table 14. 2-Wire Protocol Key
KEY
S
SAddr
FCmd
MAddr
Data
A
N
DESCRIPTION
START Bit
Slave Address (7-bit)
Function Command Byte
Memory Address Byte
Data Byte Written by Master
Acknowledge Bit (Master)
Not Acknowledge (Master)
KEY
Sr
W
R
P
Data
A
N
DESCRIPTION
Repeated START
R/ W Bit = 0
R/ W Bit = 1
STOP bit
Data Byte Returned by Slave
Acknowledge Bit (Slave)
Not Acknowledge (Slave)
assumed by the DS2777/DS2778 beginning with the
slave address acknowledge cycle. Control of the SDA
signal is retained by the DS2777/DS2778 throughout
the transaction, except for the acknowledge cycles.
The master indicates the end of a read transaction by
responding to the last byte it requires with a no
acknowledge. This signals the DS2777/DS2778 that
control of SDA is to remain with the master following the
acknowledge clock.
Write-Data Protocol
The write-data protocol is used to write to register and
shadow RAM data to the DS2777/DS2778 starting at
memory address MAddr. Data0 represents the data
written to MAddr, Data1 represents the data written to
MAddr + 1 and DataN represents the last data byte,
written to MAddr + N. The master indicates the end of a
write transaction by sending a STOP or repeated
START after receiving the last acknowledge bit.
S SAddr W A MAddr A Data0 A Data1 A … DataN A P
The MSb of the data to be stored at address MAddr
can be written immediately after the MAddr byte is
acknowledged. Because the address is automatically
incremented after the LSb of each byte is received by
the DS2777/DS2778, the MSb of the data at address
MAddr + 1 is written immediately after the acknowl-
edgement of the data at address MAddr. If the bus
master continues an autoincremented write transaction
beyond address 4Fh, the DS2777/DS2778 ignore the
data. Data is also ignored on writes to read-only
addresses and reserved addresses, locked EEPROM
blocks, as well as a write that auto-increments to the
Function Command register (address FEh). Incomplete
bytes and bytes that are not acknowledged by the
DS2777/DS2778 are not written to memory. As noted in
the Memory section, writes to unlocked EEPROM
blocks modify the shadow RAM only.
Read-Data Protocol
The read-data protocol is used to read register and
shadow RAM data from the DS2777/DS2778 starting at
a memory address specified by MAddr. Data0 repre-
sents the data byte in memory location MAddr, Data1
represents the data from MAddr + 1, and DataN repre-
sents the last byte read by the master.
S SAddr W A MAddr A Sr SAddr R A Data0 A Data1 A
… DataN N P
Data is returned beginning with the MSb of the data in
MAddr. Because the address is automatically incre-
mented after the LSb of each byte is returned, the MSb
of the data at address MAddr + 1 is available to the
host immediately after the acknowledgement of the
data at address MAddr. If the bus master continues to
read beyond address FFh, the DS2777/DS2778 output
data values of FFh. Addresses labeled reserved in the
Memory Map return undefined data. The bus master
terminates the read transaction at any byte boundary
by issuing a not acknowledge followed by a STOP or
repeated START.
Function Command Protocol
The function command protocol executes a device-
specific operation by writing one of the function com-
mand values (FCmd) to memory address FEh. Table 15
lists the DS2777/DS2778 FCmd values and describes
the actions taken by each. A 1-byte write protocol is
used to transmit the function command, with the MAddr
set to FEh and the data byte set to the desired FCmd
value. Additional data bytes are ignored. Data read
from memory address FEh is undefined.
S SAddr W A MAddr = 0FEh A FCmd A P
44
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| DS2776G+T&R | IC FUEL GAUGE LI+ 2CELL 14-TDFN |
| MAX1640EEE+T | IC SW-MODE CUR SOURCE ADJ 16QSOP |
| MAX1641EEE+T | IC SW-MODE CUR SOURCE ADJ 16QSOP |
| DS2764BE+025/T&R | IC MON BATT LI-ION HP 16-TSSOP |
| DS2764AE+025/T&R | IC MON BATT LI-ION HP 16-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2778K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2780 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
| DS2780_09 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Standalone Fuel Gauge IC |
| DS2780E | 制造商:Maxim Integrated Products 功能描述:STANDALONG FUELD GAUGE TSSOP - Rail/Tube |
| DS2780E/R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Stand-Alone Fuel Gauge IC |
发布紧急采购，3分钟左右您将得到回复。