- 您现在的位置：买卖IC网 > PDF目录1788 > DS2780G+T&R (Maxim Integrated Products)IC FUEL GAUGE STAND ALONE 10TDFN PDF资料下载
参数资料
| 型号： | DS2780G+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/31页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE STAND ALONE 10TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘 |
| 供应商设备封装： | 10-TDFN-EP（3x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页
DS2780 Standalone Fuel Gauge IC
Application Note 27, Understanding and Using Cyclic Redundancy Checks with Dallas Semiconductor Touch
Memory Products . (This application note can be found on the Maxim/Dallas Semiconductor website at
www.maxim-ic.com.)
In the circuit in Figure 19, the shift register bits are initialized to 0. Then, starting with the least significant bit of the
family code, one bit at a time is shifted in. After the 8th bit of the family code has been entered, then the serial
number is entered. After the 48th bit of the serial number has been entered, the shift register contains the CRC
value.
Figure 19. 1-Wire CRC Generation Block Diagram
INPUT
MSb
XOR
XOR
LSb
XOR
HARDWARE CONFIGURATION
Because the 1-Wire bus has only a single line, it is important that each device on the bus be able to drive it at the
appropriate time. To facilitate this, each device attached to the 1-Wire bus must connect to the bus with open-drain
or tri-state output drivers. The DS2780 uses an open-drain output driver as part of the bidirectional interface
circuitry shown in Figure 20. If a bidirectional pin is not available on the bus master, separate output and input pins
can be connected together.
The 1-Wire bus must have a pullup resistor at the bus-master end of the bus. For short line lengths, the value of
this resistor should be approximately 5k ? . The idle state for the 1-Wire bus is high. If, for any reason, a bus
transaction must be suspended, the bus must be left in the idle state to properly resume the transaction later. If the
bus is left low for more than 120 ? s (16 ? s for overdrive speed), slave devices on the bus begin to interpret the low
period as a reset pulse, effectively terminating the transaction.
The DS2780 can operate in two communication speed modes, standard and overdrive. The speed mode is
determined by the input logic level of the OVD pin; a logic 0 selects standard speed and a logic 1 selects overdrive
speed. The OVD pin must be at a stable logic level of 0 or 1 before initializing a transaction with a reset pulse. All
1-Wire devices on a multinode bus must operate at the same communication speed for proper operation. 1-Wire
timing for both standard and overdrive speeds are listed in the Electrical Characteristics: 1-Wire Interface tables.
Figure 20. 1-Wire Bus Interface Circuitry
BUS MASTER
Rx
Vpullup
(2.0V to 5.5V)
4.7k ?
DS2780 1-WIRE PORT
RX
Tx
RX = RECEIVE
TX = TRANSMIT
23 of 31
0.2 ? A
(typ)
100 ?
MOSFET
TX
相关PDF资料 |
PDF描述 |
|---|---|
| DS2781E+T&R | IC FUEL GAUGE BATT 8TSSOP |
| DS2782G-5+T&R | IC FUEL GAUGE STND-ALONE 10-TDFN |
| DS2784G+T&R | IC FUEL GAUGE STND-ALONE 14-TDFN |
| DS2786BG+T&R | IC FUEL GAUGE OCV-BASED 10-TDFN |
| DS2786G-5+T&R | IC FUEL GAUGE OCV-BASED 10-TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2780K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| DS2781 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:1-Cell or 2-Cell Standalone Fuel Gauge IC |
| DS2781AE | 制造商:Maxim Integrated Products 功能描述:2 CELL STAND ALONG FG 8P TSSOP - Rail/Tube |
| DS2781AE+ | 制造商:Maxim Integrated Products 功能描述:2 CELL STAND ALONG FG 8P TSSOP LF - Rail/Tube |
| DS2781AE+T&R | 制造商:Maxim Integrated Products 功能描述:2 CELL STAND ALONG FG 8P TSSOP LF T - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。