参数资料
| 型号： | DS2781E+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/31页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE BATT 8TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 2.5 V ~ 10 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 8-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页
DS2781
TRANSACTION SEQUENCE
The protocol for accessing the DS2781 through the 1-Wire port is as follows:
Initialization
Net Address Command
Function Command
Transaction/Data
The sections that follow describe each of these steps in detail.
All transactions of the 1-Wire bus begin with an initialization sequence consisting of a reset pulse transmitted by the
bus master followed by a presence pulse simultaneously transmitted by the DS2781 and any other slaves on the
bus. The presence pulse tells the bus master that one or more devices are on the bus and ready to operate. For
more details, see the 1-Wire Signaling section.
NET ADDRESS COMMANDS
Once the bus master has detected the presence of one or more slaves, it can issue one of the net address
commands described in the following paragraphs. The name of each ROM command is followed by the 8-bit
opcode for that command in square brackets. Figure 25 presents a transaction flowchart of the net address
commands.
Read Net Address [33h or 39h]. This command allows the bus master to read the DS2781’s 1-Wire net address.
This command can only be used if there is a single slave on the bus. If more than one slave is present, a data
collision occurs when all slaves try to transmit at the same time (open drain produces a wired-AND result). The
RNAOP bit in the status register selects the opcode for this command, with RNAOP = 0 indicating 33h, and
RNAOP = 1 indicating 39h.
Match Net Address [55h]. This command allows the bus master to specifically address one DS2781 on the 1-Wire
bus. Only the addressed DS2781 responds to any subsequent function command. All other slave devices ignore
the function command and wait for a reset pulse. This command can be used with one or more slave devices on
the bus.
Skip Net Address [CCh]. This command saves time when there is only one DS2781 on the bus by allowing the
bus master to issue a function command without specifying the address of the slave. If more than one slave device
is present on the bus, a subsequent function command can cause a data collision when all slaves transmit data at
the same time.
Search Net Address [F0h]. This command allows the bus master to use a process of elimination to identify the 1-
Wire net addresses of all slave devices on the bus. The search process involves the repetition of a simple three-
step routine: read a bit, read the complement of the bit, then write the desired value of that bit. The bus master
performs this simple three-step routine on each bit location of the net address. After one complete pass through all
64 bits, the bus master knows the address of one device. The remaining devices can then be identified on
additional iterations of the process. See Chapter 5 of the Book of DS19xx iButton Standards for a comprehensive
discussion of a net address search, including an actual example ( www.maxim-ic.com/ibuttonbook ).
Resume [A5h] . This command increases data throughput in multidrop environments where the DS2781 needs to
be accessed several times. Resume is similar to the Skip Net Address command in that the 64-bit net address
does not have to be transmitted each time the DS2781 is accessed. After successfully executing a Match Net
Address command or Search Net Address command, an internal flag is set in the DS2781. When the flag is set,
the DS2781 can be repeatedly accessed through the Resume command function. Accessing another device on the
bus clears the flag, thus preventing two or more devices from simultaneously responding to the Resume command
function.
25 of 31
相关PDF资料 |
PDF描述 |
|---|---|
| DS2782G-5+T&R | IC FUEL GAUGE STND-ALONE 10-TDFN |
| DS2784G+T&R | IC FUEL GAUGE STND-ALONE 14-TDFN |
| DS2786BG+T&R | IC FUEL GAUGE OCV-BASED 10-TDFN |
| DS2786G-5+T&R | IC FUEL GAUGE OCV-BASED 10-TDFN |
| DS2788E+T&R | IC FUEL GAUGE W/DSP DRV 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2781EVKIT+ | 制造商:Maxim Integrated Products 功能描述:1-CELL OR 2-CELL STAND-ALONE FUEL GAUGE IC - Boxed Product (Development Kits) |
| DS2781G+ | 功能描述:电池管理 1-2 Cell Stand-Alone Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| DS2781G+T&R | 制造商:Maxim Integrated Products 功能描述:2 CELL STAND ALONE FG 10-TDFN LF - Tape and Reel |
| DS2781G-A2+T&R | 制造商:Maxim Integrated Products 功能描述: |
| DS2781K | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。