- 您现在的位置：买卖IC网 > PDF目录11562 > DS3112 (Maxim Integrated Products)IC MUX TEMPE T3/E3 256-BGA PDF资料下载
参数资料
| 型号： | DS3112 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 126/133页 |
| 文件大小： | 0K |
| 描述： | IC MUX TEMPE T3/E3 256-BGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 40 |
| 控制器类型： | 调帧器，多路复用器 |
| 接口： | 并行/串行 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 150mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 256-LBGA |
| 供应商设备封装： | 256-PBGA（27x27） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页当前第126页第127页第128页第129页第130页第131页第132页第133页
DS3112
92 of 133
Bit 6: Receive Packet End (RPE). This latched read-only event-status bit will be set to a one each time the HDLC
controller detects the finish of a message whether the packet is valid (CRC correct) or not (bad CRC, abort
sequence detected, packet too small, not an integral number of octets, or an overrun occurred). This bit will be
cleared when read and will not be set again until another message end is detected. The setting of this bit can cause a
hardware interrupt to occur if the RPE bit in the Interrupt Mask for HSR (IHSR) register is set to a one and the
HDLC bit in the Interrupt Mask for MSR (IMSR) register is set to a one. The interrupt will be allowed to clear
when this bit is read.
Bit 4: Receive FIFO High Watermark (RHWM). This read-only real-time status bit will be set to a one when the
receive FIFO contains more than the number of bytes configured by the Receive High Watermark Setting control
bits (RHWMS0 to RHWMS2) in the HDLC Control Register (HCR). This bit will be cleared when the FIFO
empties below the high watermark. The setting of this bit can cause a hardware interrupt to occur if the RHWM bit
in the Interrupt Mask for HSR (IHSR) register is set to a one and the HDLC bit in the Interrupt Mask for MSR
(IMSR) register is set to a one.
Bit 5: Receive Packet Start (RPS). This latched read-only event-status bit will be set to a one each time the
HDLC controller detects an opening byte of an HDLC packet. This bit will be cleared when read and will not be set
again until another message is detected. The setting of this bit can cause a hardware interrupt to occur if the RPS bit
in the Interrupt Mask for HSR (IHSR) register is set to a one and the HDLC bit in the Interrupt Mask for MSR
(IMSR) register is set to a one. The interrupt will be allowed to clear when this bit is read.
Bit 7: Transmit FIFO Underrun (TUDR). This latched read-only event-status bit will be set to a one each time
the transmit FIFO underruns and an abort is automatically sent. This bit will be cleared when read and will not be
set again until another underrun occurs (i.e., the FIFO has been written to and then allowed to empty again). The
setting of this bit can cause a hardware interrupt to occur if the TUDR bit in the Interrupt Mask for HSR (IHSR)
register is set to a one and the HDLC bit in the Interrupt Mask for MSR (IMSR) register is set to a one. The
interrupt will be allowed to clear when this bit is read.
Bits 8 to 11: Transmit FIFO Level Bits 0 to 3 (TFL0 to TFL3). These read-only real-time status bits indicate the
current depth of the transmit FIFO with a 16-byte resolution. These status bits cannot cause a hardware interrupt.
TFL3
TFL2
TFL1
TFL0
TRANSMIT FIFO LEVEL
0
empty to 15 bytes
0
1
16 to 31 bytes
0
1
0
32 to 47 bytes
0
1
48 to 63 bytes
0
1
0
64 to 79 bytes
0
1
0
1
80 to 95 bytes
0
1
0
96 to 111 bytes
0
1
112 to 127 bytes
1
0
128 to 143 bytes
1
0
1
144 to 159 bytes
1
0
1
0
160 to 175 bytes
1
0
1
176 to 191 bytes
1
0
192 to 207 bytes
1
0
1
208 to 223 bytes
1
0
224 to 239 bytes
1
240 to 256 bytes
Bit 12: Transmit FIFO Empty (TEMPTY). This read-only real-time status bit will be set to a one when the
transmit FIFO is empty. It will be cleared when the transmit FIFO contains one or more bytes. This status bit
cannot cause a hardware interrupt.
Bit 13: Receive FIFO Overrun (ROVR). This latched read-only event-status bit will be set to a one each time the
receive FIFO overruns. This bit will be cleared when read and will not be set again until another overrun occurs
相关PDF资料 |
PDF描述 |
|---|---|
| V375A15C400BL3 | CONVERTER MOD DC/DC 15V 400W |
| V375A15C400BL2 | CONVERTER MOD DC/DC 15V 400W |
| V375A15C400B3 | CONVERTER MOD DC/DC 15V 400W |
| VE-201-IX-S | CONVERTER MOD DC/DC 12V 75W |
| V375A15C400B2 | CONVERTER MOD DC/DC 15V 400W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3112+ | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112+W | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112D1 | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112D1+ | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112DK | 功能描述:网络开发工具 DS3112 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。