- 您现在的位置：买卖IC网 > PDF目录11560 > DS3112D1+ (Maxim Integrated Products)IC MUX T3/E3 3.3V 256-PBGA PDF资料下载
参数资料
| 型号： | DS3112D1+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 80/133页 |
| 文件大小： | 0K |
| 描述： | IC MUX T3/E3 3.3V 256-PBGA |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 40 |
| 控制器类型： | 调帧器，多路复用器 |
| 接口： | 并行/串行 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 电流 - 电源： | 150mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 256-LBGA |
| 供应商设备封装： | 256-PBGA（27x27） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页当前第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页
DS3112
50 of 133
Bit 7: T3/E3 Diagnostic Loopback Enable (DLB). See Figure 1-1 and Figure 1-2 for a visual description of this
loopback.
0 = disable loopback
1 = enable loopback
Bit 8: E3 Code Violation Enable (E3CVE). This bit is ignored in the T3 mode. This bit is used in the E3 mode to
configure the BiPolar Violation Count Register (BPVCR) to count either BiPolar Violations (BPV) or Code
Violations (CV). A BPV is defined as consecutive pulses (or marks) of the same polarity that are not part of a
HDB3 codeword. A CV is defined in ITU O.161 as consecutive BPVs of the same polarity.
0 = count BPV
1 = count CV
Bits 9 and 10: T3/E3 Frame Error Counting Control Bits 0 and 1 (FECC0 and FECC1).
FECC1
FECC0
FRAME ERROR COUNT REGISTER (FECR) CONFIGURATION
0
T3 Mode: Count Loss Of Frame (LOF) Occurrences
E3 Mode: Count Loss Of Frame (LOF) Occurrences
0
1
T3 Mode: Count Both F Bit and M Bit Errors
E3 Mode: Count Bit Errors in the FAS Word
1
0
T3 Mode: Count Only F Bit Errors
E3 Mode: Count Word Errors in the FAS Word
1
T3 Mode: Count Only M Bit Errors
E3 Mode: Illegal State
Bit 11: Error Counting Control (ECC). This bit is used to control whether the device will increment the error
counters during Loss Of Frame (LOF) conditions. It only affects the error counters that count errors that are based
on framed information and these include the following:
Frame Error Counter (when it is configured to count frame errors, not LOF occurrences)
T3 Parity Bit Error Counter
T3 C-Bit Parity Error Counter
T3 Far End Block Error or E3 RAI Counter
When this bit is set low, these error counters will not be allowed to increment during LOF conditions. When this bit
is set high, these error counters will be allowed to increment during LOF conditions.
0 = stop the FECR/PCR/CPCR/FEBECR error counters from incrementing during LOF
1 = allow the FECR/PCR/CPCR/FEBECR error counters to increment during LOF
Bit 12: Automatic FEBE Defeat (AFEBED). This bit is ignored in the E3 mode and in the T3 mode when the
device is not configured in the C-Bit Parity Mode. When this bit is low, the device will automatically insert the
FEBE codes into the transmitted data stream by setting all three C bits in Subframe 4 to zero.
0 = automatically insert FEBE codes in the transmit data stream based on detected errors
1 = use the TFEBE control to determine the state of the FEBE codes
Bit 13: Transmit FEBE Setting (TFEBE). This bit is only active when AFEBED is active (i.e., AFEBED = 1).
When this bit is low, the device will force the FEBE code to 111 continuously. When this bit is set high, the device
will force the FEBE code to 000 continuously.
0 = force FEBE to 111 (null state)
1 = force FEBE to 000 (active state)
Bit 14: T3/E3 Payload Loopback Enable (PLB). See Figure 1-1 and Figure 1-2 for a visual description of this
loopback.
0 = disable loopback
1 = enable loopback
相关PDF资料 |
PDF描述 |
|---|---|
| 413959-6 | CONN PLUG BNC RG141 R/A CRIMP AU |
| VE-BTZ-IV-S | CONVERTER MOD DC/DC 2V 60W |
| VE-BTY-IV-S | CONVERTER MOD DC/DC 3.3V 99W |
| 227079-3 | CONN PLUG BNC RG59,62 CRIMP TIN |
| VE-2T1-IX-S | CONVERTER MOD DC/DC 12V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3112D1+ | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112DK | 功能描述:网络开发工具 DS3112 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| DS3112N | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112N+ | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3112N+W | 功能描述:网络控制器与处理器 IC TEMPE T3/E3 MUX FRMR & M13/E13/G.747 MUX RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。