- 您现在的位置：买卖IC网 > PDF目录9758 > DS3150TC1+ (Maxim Integrated Products)IC INTERFACE LINE 3.3V 48-TQFP PDF资料下载
参数资料
| 型号： | DS3150TC1+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 27/28页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE LINE 3.3V 48-TQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 250 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页
DS3150
8 of 28
For E3
LOS Assertion:
1) The ALOS circuitry detects that the incoming signal is less than or equal to a signal level
approximately 24dB below nominal and mutes the data coming out of the clock and data recovery
block. (24dB below nominal is in the “tolerance range” of G.775, where LOS may or may not be
declared.)
2) The DLOS detector counts 175
±75 consecutive zeros coming out of the clock and data recovery
block and asserts
LOS. (175
±75 meets the 10 N 255 pulse interval duration requirement of
G.775.)
For E3
LOS Clear:
1) The ALOS circuitry detects that the incoming signal is greater than or equal to a signal level
approximately 18dB below nominal and enables data to come out of the clock and data recovery
block. (18dB below nominal is in the “tolerance range” of G.775 where LOS may or may not be
declared.)
2) The DLOS detector counts 175
±75 consecutive pulse intervals without excessive zero occurrences
and deasserts
LOS. (175
±75 meets the 10 N 255 pulse interval duration requirement of G.775.)
The requirements of ANSI T1.231 for STS-1 LOS defects are supported by the DLOS detector. At STS-1
rate, the time required for the DLOS detector to count 175
±75 consecutive zeros falls in the range of
2.3
T100ms required by ANSI T1.231 for declaring an LOS defect. Although the time required for the
DLOS detector to count 175
±75 consecutive pulse intervals with no excessive zeros is less than the
125s to 250
ms period required by ANSI T1.231 for clearing an LOS defect, a period of this length where
LOS is inactive can easily be timed in software.
During LOS, the RCLK output signal is derived from the device’s master clock. The ALOS detector has a
longer time constant than the DLOS detector. Thus, when the incoming signal is lost, the DLOS detector
activates first, asserting the
LOS pin, followed by the ALOS detector. When a signal is restored, the
DLOS detector does not get a valid signal that it can qualify for no excessive zero occurrences until the
ALOS detector has seen the incoming signal rise above a signal level approximately 18dB below
nominal.
Framer Interface Format and the B3ZS/HDB3 Decoder. The recovered data can be output in
either NRZ or bipolar format. To select the bipolar format, wire the
ZCSE input pin high. In this format,
the B3ZS/HDB3 decoder is disabled, and the recovered data is buffered and output on the RPOS and
RNEG output pins. Received positive-polarity pulses are indicated by RPOS = 1, while negative-polarity
pulses are indicated by RNEG = 1. In bipolar interface format the receiver simply passes on the data
received and does not check it for bipolar violations or excessive zero occurrences.
To select the NRZ format, wire
ZCSE low. In this format, the B3ZS/HDB3 decoder is enabled, and the
recovered data is decoded and output as a composite NRZ value on the RNRZ pin. Code violations are
flagged on the RLCV pin. In the discussion that follows, a valid pulse that conforms to the AMI rule is
denoted as B. A pulse that violates the AMI rule is known as bipolar violation (BPV) and is denoted as V.
In DS3 and STS-1 modes, B3ZS decoding is performed. RLCV is asserted during any RCLK cycle where
the data on RNRZ causes ones of the following code violations:
§ A BPV immediately preceded by a valid pulse (B, V)
§ A BPV with the same polarity as the last BPV
相关PDF资料 |
PDF描述 |
|---|---|
| VI-244-MX-F2 | CONVERTER MOD DC/DC 48V 75W |
| MS3116J8-2S | CONN PLUG 2POS STRAIGHT W/SCKT |
| MC100EP16VCDG | IC RCVR/DRVR ECL DIFF 5V 8SOIC |
| VI-243-MX-F4 | CONVERTER MOD DC/DC 24V 75W |
| HI5767/6CB-T | CONV A/D 10BIT 60MSPS 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3150TC1+ | 功能描述:网络控制器与处理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3150TN | 功能描述:网络控制器与处理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3150TN+ | 功能描述:网络控制器与处理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS3150TN1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS3150TNC1 | 功能描述:网络控制器与处理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。