参数资料
| 型号： | DS3231SN#T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 4/20页 |
| 文件大小： | 0K |
| 描述： | IC RTC W/TCXO 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 类型： | 时钟/日历 |
| 特点： | 警报器，闰年，方波输出，TCXO/晶体 |
| 时间格式： | HH:MM:SS（12/24 小时） |
| 数据格式： | YY-MM-DD-dd |
| 接口： | I²C，2 线串口 |
| 电源电压： | 2.3 V ~ 5.5 V |
| 电压 - 电源，电池： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
Extremely Accurate I2C-Integrated
RTC/TCXO/Crystal
12
Maxim Integrated
DS3231
the binary-coded decimal (BCD) format. The DS3231
can be run in either 12-hour or 24-hour mode. Bit 6 of
the hours register is defined as the 12- or 24-hour
mode select bit. When high, the 12-hour mode is
selected. In the 12-hour mode, bit 5 is the
AM/PM bit
with logic-high being PM. In the 24-hour mode, bit 5 is
the 20-hour bit (20–23 hours). The century bit (bit 7 of
the month register) is toggled when the years register
overflows from 99 to 00.
The day-of-week register increments at midnight.
Values that correspond to the day of week are user-
defined but must be sequential (i.e., if 1 equals
Sunday, then 2 equals Monday, and so on). Illogical
time and date entries result in undefined operation.
When reading or writing the time and date registers, sec-
ondary (user) buffers are used to prevent errors when
the internal registers update. When reading the time and
date registers, the user buffers are synchronized to the
internal registers on any START and when the register
pointer rolls over to zero. The time information is read
from these secondary registers, while the clock contin-
ues to run. This eliminates the need to reread the regis-
ters in case the main registers update during a read.
The countdown chain is reset whenever the seconds regis-
ter is written. Write transfers occur on the acknowledge
from the DS3231. Once the countdown chain is reset, to
avoid rollover issues the remaining time and date registers
must be written within 1 second. The 1Hz square-wave out-
put, if enabled, transitions high 500ms after the seconds
data transfer, provided the oscillator is already running.
Alarms
The DS3231 contains two time-of-day/date alarms.
Alarm 1 can be set by writing to registers 07h to 0Ah.
Alarm 2 can be set by writing to registers 0Bh to 0Dh.
The alarms can be programmed (by the alarm enable
and INTCN bits of the control register) to activate the
INT/SQW output on an alarm match condition. Bit 7 of
each of the time-of-day/date alarm registers are mask
bits (Table 2). When all the mask bits for each alarm
are logic 0, an alarm only occurs when the values in the
timekeeping registers match the corresponding values
stored in the time-of-day/date alarm registers. The
alarms can also be programmed to repeat every sec-
ond, minute, hour, day, or date. Table 2 shows the pos-
sible settings. Configurations not listed in the table will
result in illogical operation.
The DY/
DT bits (bit 6 of the alarm day/date registers)
control whether the alarm value stored in bits 0 to 5 of
that register reflects the day of the week or the date of
the month. If DY/
DT is written to logic 0, the alarm will
be the result of a match with date of the month. If
DY/
DT is written to logic 1, the alarm will be the result of
a match with day of the week.
When the RTC register values match alarm register set-
tings, the corresponding Alarm Flag ‘A1F’ or ‘A2F’ bit is
set to logic 1. If the corresponding Alarm Interrupt
Enable ‘A1IE’ or ‘A2IE’ is also set to logic 1 and the
INTCN bit is set to logic 1, the alarm condition will acti-
vate the
INT/SQW signal. The match is tested on the
once-per-second update of the time and date registers.
Table 2. Alarm Mask Bits
ALARM 1 REGISTER MASK BITS (BIT 7)
DY/
DT
A1M4
A1M3
A1M2
A1M1
ALARM RATE
X
1
Alarm once per second
X
1
0
Alarm when seconds match
X
1
0
Alarm when minutes and seconds match
X
1
0
Alarm when hours, minutes, and seconds match
0
Alarm when date, hours, minutes, and seconds match
1
0
Alarm when day, hours, minutes, and seconds match
ALARM 2 REGISTER MASK BITS (BIT 7)
DY/
DT
A2M4
A2M3
A2M2
ALARM RATE
X
1
Alarm once per minute (00 seconds of every minute)
X
1
0
Alarm when minutes match
X
1
0
Alarm when hours and minutes match
0
Alarm when date, hours, and minutes match
1
0
Alarm when day, hours, and minutes match
相关PDF资料 |
PDF描述 |
|---|---|
| DS3232MZ+ | IC RTC W/SRAM I2C 8SOIC |
| DS3232SN#T&R | IC RTC W/TCXO 20-SOIC |
| DS3234S# | IC RTC W/TCXO 20-SOIC |
| DS32C35-33#T&R | IC RTC ACCURATE I2C 3.3V 20-SOIC |
| DS3911T+ | IC DAC 10BIT I2C QUAD 14TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3232 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Extremely Accurate I2C RTC with Integrated Crystal and SRAM |
| DS3232_07 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Extremely Accurate I2C RTC with Integrated Crystal and SRAM |
| DS3232_08 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Extremely Accurate I2C RTC with Integrated Crystal and SRAM |
| DS3232_10 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Extremely Accurate I2C RTC with Integrated Crystal and SRAM |
| DS3232-3+ | 功能描述:实时时钟 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。