- 您现在的位置：买卖IC网 > PDF目录1916 > DS3502U+ (Maxim Integrated Products)IC POT DGTL NV 128TAP 10-MSOP PDF资料下载
参数资料
| 型号： | DS3502U+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/11页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL NV 128TAP 10-MSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 556 |
| 接片： | 128 |
| 电阻（欧姆）： | 10k |
| 电路数： | 1 |
| 温度系数： | 标准值 ±4 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 管件 |
DS3502
High-Voltage, NV, I2C POT
8
_______________________________________________________________________________________
data bit is valid at the rising edge of the current SCL
pulse. Remember that the master generates all SCL
clock pulses, including when it is reading bits from the
slave.
Acknowledge (ACK and NACK): An Acknowledge
(ACK) or Not Acknowledge (NACK) is always the 9th bit
transmitted during a byte transfer. The device receiving
data (the master during a read or the slave during a
write operation) performs an ACK by transmitting a 0
during the 9th bit. A device performs a NACK by trans-
mitting a 1 during the 9th bit. Timing for the ACK and
NACK is identical to all other bit writes. An ACK is the
acknowledgment that the device is properly receiving
data. A NACK is used to terminate a read sequence or
indicates that the device is not receiving data.
Byte write: A byte write consists of 8 bits of information
transferred from the master to the slave (most signifi-
cant bit first) plus a 1-bit acknowledgment from the
slave to the master. The 8 bits transmitted by the mas-
ter are done according to the bit write definition and the
acknowledgment is read using the bit read definition.
Byte read: A byte read is an 8-bit information transfer
from the slave to the master plus a 1-bit ACK or NACK
from the master to the slave. The 8 bits of information
that are transferred (most significant bit first) from the
slave to the master are read by the master using the bit
read definition above, and the master transmits an ACK
using the bit write definition to receive additional data
bytes. The master must NACK the last byte read to ter-
minate communication so the slave will return control of
SDA to the master.
Slave address byte: Each slave on the I2C bus
responds to a slave address byte sent immediately fol-
lowing a START condition. The slave address byte con-
tains the slave address in the most significant 7 bits
and the R/W bit in the least significant bit. The slave
address byte of the DS3502 is shown in Figure 1.
When the R/W bit is 0 (such as in 50h), the master is
indicating it will write data to the slave. If R/W = 1 (51h
in this case), the master is indicating it wants to read
from the slave.
If an incorrect slave address is written, the DS3502
assumes the master is communicating with another I2C
device and ignores the communication until the next
START condition is sent.
Memory address: During an I2C write operation, the
master must transmit a memory address to identify the
memory location where the slave is to store the data.
The memory address is always the second byte trans-
mitted during a write operation following the slave
address byte.
I2C Communication
Writing a single byte to a slave: The master must gen-
erate a START condition, write the slave address byte
(R/W = 0), write the memory address, write the byte of
data, and generate a STOP condition. Remember the
master must read the slave’s acknowledgment during
all byte write operations.
When writing to the DS3502, the potentiometer adjusts to
the new setting once it has acknowledged the new data
that is being written, and the EEPROM is written following
the STOP condition at the end of the write command. To
change the setting without changing the EEPROM, termi-
nate the write with a repeated START condition before
the next STOP condition occurs. Using a repeated
START condition prevents the tW delay required for the
EEPROM write cycle to finish.
Acknowledge polling: Any time a EEPROM byte is
written, the DS3502 requires the EEPROM write time
(tW) after the STOP condition to write the contents of
the byte to EEPROM. During the EEPROM write time,
the device will not acknowledge its slave address
because it is busy. It is possible to take advantage of
this phenomenon by repeatedly addressing the
DS3502, which allows communication to continue as
soon as the DS3502 is ready. The alternative to
acknowledge polling is to wait for a maximum period of
tW to elapse before attempting to access the device.
EEPROM write cycles: The DS3502’s EEPROM write
cycles are specified in the
Nonvolatile Memory
Characteristics table. The specification shown is at the
worst-case temperature (hot) as well as at room tem-
perature. Writing to the WR/IVR register with MODE = 1
does not count as a EEPROM write.
Reading a single byte from a slave: Unlike the write
operation that uses the specified memory address byte
to define where the data is to be written, the read opera-
tion occurs at the present value of the memory address
counter. To read a single byte from the slave, the master
generates a START condition, writes the slave address
byte with R/W = 1, reads the data byte with a NACK to
indicate the end of the transfer, and generates a STOP
condition. However, since requiring the master to keep
track of the memory address counter is impractical, the
following method should be used to perform reads from
a specified memory location.
相关PDF资料 |
PDF描述 |
|---|---|
| DS3503U+ | IC POT DGTL NV 128TAP 10-MSOP |
| DS3897MX | IC TXRX BTL TRAPEZIODAL 20-SOIC |
| DS3901E+ | IC RESIST VAR TRPL 14TSSOP |
| DS3902U-530+T&R | IC DIGITAL RESISTER EEPROM 8USOP |
| DS3903E-020/T&R | IC POT NV TRIPLE 128POS 20-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3502U+ | 功能描述:数字电位计 IC High-Voltage NV I2C RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS3502U+T&R | 制造商:Maxim Integrated Products 功能描述:MXMDS3502U+T&R HIGH-VOLTAGE NV I?°?C POTEN 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 128POS 10KOHM SGL 10USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DGTL NV 128TAP 10-MSOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs High-Voltage NV I2C |
| DS3502U+T&R/C | 制造商:Maxim Integrated Products 功能描述:DIGITAL POTENTIOMETER 128POS 10KOHM SINGLE 10-PIN USOP T/R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DGTL NV 128TAP 10-USOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs High-Voltage NV I2C |
| DS3502U+T&R | 功能描述:数字电位计 IC High-Voltage NV I2C RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS3502U+T&R/C | 功能描述:数字电位计 IC High-Voltage NV I2C RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。