参数资料
型号: DS3881E+C
厂商: Maxim Integrated
文件页数: 9/28页
文件大小: 0K
描述: IC CCFL CONTROL 24TSSOP
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 62
类型: CCFL 控制器
频率: 40 ~ 100 kHz
电流 - 电源: 12mA
电源电压: 4.75 V ~ 5.25 V
工作温度: -40°C ~ 105°C
封装/外壳: 24-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 24-TSSOP
包装: 管件
其它名称: DS3881E+
DS3881E+-ND
Single-Channel Automotive CCFL Controller
Functional Diagrams (continued)
LAMP OUT
300mV
CHANNEL ENABLE
LCM1
CHANNEL FAULT
DIGITAL
LAMP OVERCURRENT
LOCE BIT IN CR1.0
2.5V
LAMP CURRENT
MONITOR
CCFL
CONTROLLER
LAMP STRIKE AND REGULATION
DIMMING PWM SIGNAL
64 LAMP CYCLE
INTEGRATOR
OVERVOLTAGE
V LRT (1.0V NOMINAL)
OVD1
512 x LAMP FREQUENCY
[20.48MHz ~ 51.20MHz]
LAMP MAXIMUM VOLTAGE REGULATION
1.0V
OVERVOLTAGE DETECTOR
LAMP FREQUENCY
[40kHz ~ 80kHz]
GATE
DRIVERS
GA1
GB1
MOSFET
GATE
DRIVERS
Figure 2. Per Channel Logic Diagram
Detailed Description
The DS3881 uses a push-pull drive scheme to convert
a DC voltage (8V to 16V) to the high-voltage (300V RMS
to 1000V RMS ) AC waveform that is required to power
the CCFL. The push-pull drive scheme uses a minimal
number of external components, which reduces assem-
bly cost and makes the printed circuit board design
easy to implement. The push-pull drive scheme also
provides an efficient DC-to-AC conversion and pro-
duces near-sinusoidal waveforms.
Each DS3881 drives two logic-level n-channel
MOSFETs that are connected between the ends of a
step-up transformer and ground (see the Typical
Operating Circuit). The transformer has a center tap on
the primary side that is connected to a DC voltage sup-
ply. The DS3881 alternately turns on the two MOSFETs
to create the high-voltage AC waveform on the sec-
ondary side. By varying the duration of the MOSFET
turn-on times, the CCFL current is able to be accurately
controlled.
A resistor in series with the CCFL’s ground connection
enables current monitoring. The voltage across this
resistor is fed to the lamp current monitor (LCM) input
and compared to an internal reference voltage to deter-
mine the duty cycle for the MOSFET gates. The CCFL
receives current monitoring and control, which maxi-
mizes the lamp’s brightness and lifetime.
Block diagrams of the DS3881 are shown in Figures 1
and 2. More operating details of the DS3881 are dis-
cussed on the following pages of this data sheet.
Memory Registers and
I2C-Compatible Serial Interface
The DS3881 uses an I 2 C-compatible serial interface for
communication with the on-board EEPROM and SRAM
configuration/status registers as well as user memory.
The configuration registers, which are a mixture of
shadowed EEPROM and SRAM, allow the user to cus-
tomize many DS3881 parameters such as the soft-start
ramp rate, the lamp and dimming frequency sources,
brightness of the lamps, fault-monitoring options, chan-
nel enabling/disabling, EMI control, and lamp current
overdrive control. The eight bytes of NV user memory
can be used to store manufacturing data such as date
codes, serial numbers, or product identification num-
bers. The device is shipped from the factory with the
configuration registers programmed to a set of default
configuration parameters. To inquire about custom pro-
gramming, contact the factory.
_____________________________________________________________________
9
相关PDF资料
PDF描述
EBC05DRTS-S93 CONN EDGECARD 10POS DIP .100 SLD
DAL7W2S500G40LF CONN DSUB RCPT 7W2 T/H R/A GOLD
EYM06DRMD CONN EDGECARD 12POS .156 WW
GEC13DRXN-S734 CONN EDGECARD 26POS DIP .100 SLD
PSA075-120 POWER SUPPLY OPEN FRAME 75W
相关代理商/技术参数
参数描述
DS3881ER 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Channel Automotive CCFL Controller
DS3881ET 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Channel Automotive CCFL Controller
DS3882 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Channel Automotive CCFL Controller
DS3882_10 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Channel Automotive CCFL Controller
DS3882E 制造商:Maxim Integrated Products 功能描述:CAR DUAL CCFL CONTROL TSSOP - 28 - Rail/Tube