- 您现在的位置：买卖IC网 > PDF目录19308 > DS3882E+C (Maxim Integrated)IC CCFL CNTRLR DUAL 28TSSOP PDF资料下载
参数资料
| 型号： | DS3882E+C |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/31页 |
| 文件大小： | 0K |
| 描述： | IC CCFL CNTRLR DUAL 28TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 72 |
| 类型： | CCFL 控制器 |
| 频率： | 40 ~ 100 kHz |
| 电流 - 电源： | 12mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 其它名称： | Q3390330 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Dual-Channel Automotive CCFL Controller
Pin Description (continued)
NAME
POSC
A1
GND_S
SVML
SVMH
V CC
N.C.
STEP
GND
LCO
PDN
PIN
9
10
11
12
13
14, 24
19
20
21
22
23
FUNCTION
DPWM Oscillator Resistor Adjust. A resistor to ground on this lead sets the frequency of the DPWM
oscillator. This lead can optionally accept a 22.5Hz to 440Hz clock that will become the source timing of
the internal DPWM signal.
Address Select Input. Determines I 2 C slave address.
I 2 C Interface Ground Connection. GND_S must be at the same potential as GND.
Low-Supply Voltage Monitor Input. Used to monitor the inverter voltage for undervoltage conditions.
High-Supply Voltage Monitor Input. Used to monitor the inverter voltage for overvoltage conditions.
Power-Supply Connections. Both pins must be connected.
No Connection. Do not connect any signal to this pin.
Lamp Frequency Step Input. This active-high digital input moves the lamp oscillator frequency up or
down by 1%, 2%, 3%, or 4% as configured in the EMIC register. This pin is logically ORed with
the STEPE bit in the EMIC register.
Ground Connection
Lamp Current Overdrive Enable Input. A high digital level at this input enables the lamp current
overdrive circuit. The amount of overdrive current is configured by the LCOC register. When this input is
low, the lamp current is set to its nominal level. This pin is logically ORed with the LCOE bit in the LCOC
register.
Lamp On/Off Control Input. A low digital level at this input turns the lamp on. A high digital level turns the
lamps off, clears the fault logic, and places the device into the power-down mode. The high-to-low
transition on this input issues a controller reset, which clears the fault logic and reinitiates a lamp strike.
This pin is logically ORed with the PDNE bit in the CR2 register.
8
_____________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ESM08DRMI | CONN EDGECARD 16POS .156 SQ WW |
| RW2-483.3D | CONV DC/DC 2W 36-72VIN +/-3.3V |
| ASM28DRMI | CONN EDGECARD 56POS .156 SQ WW |
| GBM06DCTN-S288 | CONN EDGECARD 12POS .156 EXTEND |
| KA7805AE | IC REG LDO 5V 1A TO-220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3882ER | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Channel Automotive CCFL Controller |
| DS3882ET | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Dual-Channel Automotive CCFL Controller |
| DS3883 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:BTL 9-Bit Data Transceiver |
| DS3883 WAF | 制造商:Texas Instruments 功能描述: |
| DS3883A | 制造商:NSC 制造商全称:National Semiconductor 功能描述:BTL 9-Bit Data Transceiver |
发布紧急采购，3分钟左右您将得到回复。