- 您现在的位置：买卖IC网 > PDF目录19276 > DS3991Z+PP/V (Maxim Integrated)IC CTRLR CCFL PUSH-PULL 16-SOIC PDF资料下载
参数资料
| 型号： | DS3991Z+PP/V |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/16页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR CCFL PUSH-PULL 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | CCFL 控制器 |
| 频率： | 40 ~ 80 kHz |
| 电流 - 电源： | 5mA |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 管件 |
| 其它名称： | 90-3991Z+V01 |
Low-Cost CCFL Controller
BURST-DIMMING PWM SIGNAL
(EITHER CREATED INSIDE THE DS3991 OR
SOURCED AT THE POSC/PWM PIN)
80Hz TO 300Hz
LAMP CURRENT
SOFT-START
Figure 1. Digital PWM Dimming and Soft-Start
If the PWM_EN pin is tied high, the digital control
method is enabled and an external PWM signal
between 80Hz and 300Hz is applied at the POSC/PWM
pin to set the brightness of the lamp. In the digital con-
trol method, the SLOPE and BRIGHT pins are not used.
Lamp Strike
On lamp strike, the DS3991 boosts the normal operating
lamp frequency by 33%. This is done to increase the
voltage created and help ensure that the lamp strikes.
Once the controller detects that the lamp has struck, the
frequency is returned to the normal lamp frequency.
Setting the Lamp and DPWM Frequencies Using
External Resistors
Both the lamp and DPWM frequencies are set using
external resistors. The resistance required for either fre-
quency can be determined using the following formula:
Supply Monitoring
The DS3991 has supply-voltage monitors (SVML and
SVMH) for the inverter ’s DC supply (V INV ) and an
undervoltage lockout for the V CC supply to ensure that
voltage levels are adequate for proper operation. The
inverter supply is monitored for overvoltage conditions
at the SVMH pin and undervoltage conditions at the
SVML pin. External resistor-dividers at each SVM input
feed into two comparators, both having 2V thresholds
(see Figure 2). Using the equation below to determine
the resistor values, the SVMH and SVML trip points
(V TRIP ) can be customized to shut off the inverter when
the inverter supply voltage rises above or drops below
specified values.
Operating with the inverter supply at too low of a level can
prevent the transformer from reaching the strike voltage
and could potentially cause numerous other problems.
Operating with the inverter voltage at too high of a level
R OSC =
K
f OSC
can be damaging to the inverter components. Proper use
of the SVMs can prevent these problems. If desired, the
high and/or low SVMs can be disabled by connecting the
R 1 + R 2
where K = 4000kΩ x kHz for lamp frequency calcula-
tions, K = 4k Ω x kHz for DPWM frequency calculations.
Example: Select the resistor values to configure the
DS3991 to have a 50kHz lamp frequency and a 160Hz
DPWM frequency. For the DPWM resistor calculation, K
= 4k Ω x kHz. For the lamp frequency resistor (R LOSC )
calculation, K = 4000k Ω x kHz. The formula above can
now be used to calculate the resistor values for R LOSC
and R POSC as follows:
SVMH pin to GND and the SVML pin to VCC.
V TRIP = 2.0
R 1
The SVMH and SVML are high-impedance inputs and
noise on the inverter supply can cause the monitors to
inadvertently trigger even though the inputs contain hys-
teresis. The user may wish to add a lowpass filter to
R LOSC =
4000k
50kHz
kHz
= 80k
reduce the noise present at the SVMH and SVML inputs.
The V CC monitor is a 5V supply undervoltage lockout
(UVLO) that prevents operation when the DS3991 does
R POSC =
4k kHz
0.160kHz
= 25k
not have adequate voltage for its analog circuitry to
operate or to drive the external MOSFETs. The V CC
monitor features hysteresis to prevent V CC noise from
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| GCM06DTKT-S288 | CONN EDGECARD 12POS .156 EXTEND |
| TAP686K016CRW | CAP TANT 68UF 16V 10% RADIAL |
| KA78RM33TSTU | IC REG LDO 3.3V .5A TO-220 |
| GEM22DTKN-S288 | CONN EDGECARD 44POS .156 EXTEND |
| KA78RM33TU | IC REG LDO 3.3V .5A TO-220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3992 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
| DS3992Z+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS3992Z-09N | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
| DS3992Z-09N+ | 功能描述:显示驱动器和控制器 2Ch Push-Pull CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| DS3992Z-09N+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
发布紧急采购，3分钟左右您将得到回复。