- 您现在的位置：买卖IC网 > PDF目录19278 > DS3991Z+T&R/PP (Maxim Integrated)IC CTRLR CCFL PUSH-PULL 16-SOIC PDF资料下载
参数资料
| 型号： | DS3991Z+T&R/PP |
| 厂商： | Maxim Integrated |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR CCFL PUSH-PULL 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | CCFL 控制器 |
| 频率： | 40 ~ 80 kHz |
| 电流 - 电源： | 5mA |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | 90-3991V+001 |
Low-Cost CCFL Controller
that the lamp has struck by detecting current flow in the
lamp. If during the strike ramp, the maximum allowable
voltage is reached, the controller stops increasing the
MOSFET gate duty cycle to keep from overstressing the
system. The DS3991 goes into a fault-handling state if
the lamp has not struck after 65,536 lamp cycles. If an
overvoltage event is detected during the strike attempt,
the DS3991 disables the MOSFET gate drivers and
goes into the fault handling state.
Once the lamp is struck, the DS3991 moves to the run-
lamp stage. In the run-lamp stage, the DS3991 adjusts
the MOSFET gate duty cycle to optimize the lamp cur-
rent. The gate duty cycle is always constrained to keep
the system from exceeding the maximum allowable
lamp voltage. If lamp current ever drops below the
lamp-out reference point for 65,536 lamp cycles, the
lamp is considered extinguished. In this case the MOS-
FET gate drivers are disabled and the device moves to
the fault-handling stage.
In the case of a lamp overcurrent, the DS3991 instanta-
neously declares the controller to be in a fault state. If
the DS3991 goes into the fault state, the DS3991 shuts
down. Once a fault state is entered, the controller
remains in that state until one of the following occurs:
? V CC drops below the UVLO threshold
? SVML input drops below 2.0V
? SVMH input goes above 2.0V
Applications Information
Component Selection
External component selection has a large impact on the
overall system performance and cost. The two most
important external components are the transformers
and MOSFETs.
The transformer should be able to operate in the 40kHz
to 80kHz frequency range of the DS3991, and the turns
ratio should be selected so the MOSFET drivers run at
28% to 35% duty cycle during steady-state operation.
The transformer must be able to withstand the high
open-circuit voltage that is used to strike the lamp.
Additionally, its primary/secondary resistance and
inductance characteristics must be considered
because they contribute significantly to determining the
efficiency and transient response of the system. Table 1
shows a transformer specification that has been utilized
for a 12V inverter supply, 438mm x 2.2mm lamp design.
The MOSFETs must have a threshold voltage that is low
enough to work with logic-level signals, a low on-resis-
tance to maximize efficiency and limit the MOSFET’s
power dissipation, and a breakdown voltage high
enough to handle the transient. For push-pull topolo-
gies, the breakdown voltage of the MOSFETs should be
a minimum of 3x the inverter voltage supply.
Additionally, the total gate charge must be less than
Q G , which is specified in the Recommended Operating
Conditions table.
Table 1. Transformer Specifications (as used in the Typical Operating Circuits)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Turns Ratio (Secondary/Primary) Push-Pull Type
(Notes 1, 2, 3)
40
Turns Ratio (Secondary/Primary) Half-Bridge Type (Note 3)
80
Frequency
Output Power
Output Current
40
5
80
6
8
kHz
W
mA
Primary DCR
Secondary DCR
Primary Leakage
Secondary Leakage
Primary Inductance
Secondary Inductance
Secondary Output Voltage
Center tap to one end
1000ms (min)
Continuous
2000
1000
200
500
12
185
70
500
m
μH
mH
μH
mH
V RMS
Note 1: Primary should be bifilar wound with center-tap connection.
Note 2: Turns ratio is defined as secondary winding divided by the sum of both primary windings.
Note 3: This is the nominal turns ratio for driving a 438mm x 2.2mm lamp with a 12V supply. Refer to Application Note 3375 for more
information on push-pull type applications.
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| V300B3V3T150BL2 | CONVERTER MOD DC/DC 3.3V 150W |
| ECC08DCMI | CONN EDGECARD 16POS .100 WW |
| TAJD336K025HNJ | CAP TANT 33UF 25V 10% 2917 |
| GSC50DRAN | CONN EDGECARD 100PS R/A .100 SLD |
| GMC50DRAN | CONN EDGECARD 100PS R/A .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3992 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
| DS3992Z+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS3992Z-09N | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
| DS3992Z-09N+ | 功能描述:显示驱动器和控制器 2Ch Push-Pull CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| DS3992Z-09N+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
发布紧急采购，3分钟左右您将得到回复。