参数资料
| 型号： | DS3992Z-09N+T&R |
| 厂商： | Maxim Integrated |
| 文件页数： | 8/13页 |
| 文件大小： | 0K |
| 描述： | IC CCFL CNTRLR 2CH 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | CCFL 控制器 |
| 频率： | 40 ~ 80 kHz |
| 电流 - 电源： | 8mA |
| 电源电压： | 4.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
Two-Channel, Push-Pull CCFL Controller
Table 1. BRIGHT Analog Dimming Input Configuration
DEVICE
DS3992Z-09P and DS3992Z-18P
DS3992Z-09N and DS3992Z-18N
SLOPE
Positive
Negative
MINIMUM BRIGHTNESS
BRIGHT < 0.5V
BRIGHT > 2.0V
MAXIMUM BRIGHTNESS
BRIGHT > 2.0V
BRIGHT < 0.5V
during this time. During the low period of the DPWM
cycle, the controller disables the MOSFET gate drivers
so the lamp is not driven. This causes the current to
The previous formula can now be used to calculate the
resistor values for R LOSC and R POSC as follows:
stop flowing in the lamp, but the time is short enough to
keep the lamp from de-ionizing. Dimming is increased/
R LOSC =
1600 k Ω x kHz
50 kHz
= 32 k Ω
V TRIP = 2 . 0 ? 1 2 ?
decreased by adjusting (i.e., modulating) the burst
period duty cycle. At the beginning of each burst dim-
ming cycle, there is a soft-start whereby the lamp cur-
rent is slowly ramped to reduce the potential to create
audible transformer noise.
The slope of the BRIGHT dimming input is either posi-
tive or negative as shown in Table 1. For voltages
between 0.5V and 2.0V, the duty cycle will vary linearly
between the minimum and 100%.
Lamp Strike
On lamp strike, the DS3992 boosts the normal operat-
ing lamp frequency by 33%. This is done to increase
the voltage created and help insure that the lamp
strikes. In addition, the maximum strike voltage will be
applied to the lamp for over 500ms. Once the controller
detects that the lamp has struck, the frequency is
returned to the normal lamp frequency.
Setting the Lamp and DPWM Frequencies
Using External Resistors
Both the lamp and DPWM frequencies are set using
external resistors. The resistance required for either fre-
quency can be determined using the following formula:
4 k Ω x kHz
R POSC = = 25 k Ω
0 . 160 kHz
Supply Monitoring
The DS3992 has supply voltage monitors for both the
inverter’s DC supply (V INV ) and its own V CC supply to
ensure that both voltage levels are adequate for proper
operation. The inverter supply is monitored for under-
voltage conditions at the SVM pin. An external resistor-
divider at the SVM input feeds into a comparator (see
Figure 1) having a 2V threshold. Using the equation
below to determine the resistor values, the inverter sup-
ply trip point (V TRIP ) can be customized to shut off the
inverter when the inverter supply voltage drops below
the specified value.
Operating with the inverter voltage at too high of a level
can be damaging to the inverter components. Proper
use of the SVM can prevent this problem. If desired, SVM
can be disabled by connecting the SVM pin to GND.
? R + R ?
? R 1 ?
R OSC =
K
f OSC
The V CC monitor is a 5V supply undervoltage lockout
(UVLO) that prevents operation when the DS3992 does
not have adequate voltage for its analog circuitry to
where K = 1600k Ω x kHz for lamp frequency calcula-
tions. When calculating the resistor value for the DPWM
frequency, K will be one of two values depending on
the DS3992 version. If using the -09N/P version (90Hz
to 220Hz) then K = 4k Ω x kHz. K = 8k Ω x kHz for the
-18N/P version (180Hz to 440Hz).
Example: Selecting the resistor values to configure the
-09P version to have a 50kHz lamp frequency and a
160Hz DPWM frequency: For the DPWM resistor calcula-
tion, K = 4k Ω x kHz. For the lamp-frequency-resistor
(R LOSC ) calculation, K = 1600k Ω x kHz, which is always
the lamp frequency K value regardless of the frequency.
operate or to drive the external MOSFETs. The V CC
monitor features hysteresis to prevent V CC noise from
causing spurious operation when V CC is near the trip
point. This monitor cannot be disabled by any means.
Fault Monitoring
The DS3992 provides extensive fault monitoring for
each channel. It can detect open-lamp, lamp overcur-
rent, failure to strike, and overvoltage conditions. Figure
4 shows a flowchart of how the DS3992 controls and
monitors each channel. The steps are as follows:
The lamps will not turn on unless the DS3992 supply
voltage is > 4.5V and the voltage at the supply voltage
monitor (SVM) input is > 2V.
8
_____________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| DS3994Z+T&R | IC CCFL CNTRLR 4CH 28-SOIC |
| DS4303R-U+ | IC VREF SERIES ADJ SOT-23-5 |
| DS4510U-5/T&R | IC SUPERVISOR W/NV MEM 5-USOP |
| DS4510U+ | IC SUPERVISOR W/NV MEM 10-USOP |
| DW-16-12-G-D-665 | CONN HEADER 32POS DUAL 2.54MM AU |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS3992Z-09P | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
| DS3992Z-09P+ | 功能描述:显示驱动器和控制器 2Ch Push-Pull CCFL Controller RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| DS3992Z-09P+R | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
| DS3992Z-09P+T | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Two-Channel, Push-Pull CCFL Controller |
| DS3992Z-09P+T&R | 制造商:Maxim Integrated Products 功能描述: 制造商:Maxim Integrated Products 功能描述:CCFL DRVR 5.5V 16SOIC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC CCFL CNTRLR 2CH 16-SOIC |
发布紧急采购，3分钟左右您将得到回复。