- 您现在的位置：买卖IC网 > PDF目录9187 > DS4301U-200+T&R (Maxim Integrated Products)IC POT DIG NV 200K 32POS 8-USOP PDF资料下载
参数资料
| 型号： | DS4301U-200+T&R |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/7页 |
| 文件大小： | 0K |
| 描述： | IC POT DIG NV 200K 32POS 8-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 3,000 |
| 接片： | 32 |
| 电阻（欧姆）： | 200k |
| 电路数： | 1 |
| 温度系数： | 标准值 ±250 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 3 线（芯片选择，递增，增/减） |
| 电源电压： | 2.4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 带卷 (TR) |
DS4301
Detailed Description
The DS4301 is a single nonvolatile digital potentiome-
ter. This 32-position linear potentiometer has an end-to-
end resistance of 200k
, and operates over a wide
2.4V to 5.5V supply voltage range. The wiper position is
controlled by the three interface pins (U/D, CS, and
INC), and the wiper setting can be stored in EEPROM
on command.
Power-Up
On power-up, once a stable supply voltage of VCC MIN
has been reached, the stored wiper setting is loaded
from the EEPROM within tWLT. Also on power-up, the
DS4301 wiper control pins become active approximate-
ly tPU after a stable supply voltage of VCC MIN has
been reached.
Wiper Control
Adjusting the wiper of the DS4301 involves using the
three control pins (U/D, CS, and INC). See the Timing
Diagram in Figure 2. To enable wiper adjustment, a
high-to-low transition on the CS pin is required. Hold
CS low for the duration of the communication. Doing
this enables the INC pin to change the wiper position.
Set the U/D pin high to increment or low to decrement
the wiper position. The state of the U/D pin should be
set more than tDI before the INC signal is transitioned
from high to low. After the CS pin is active low, a high-
to-low transition on the INC pin moves the wiper in the
direction dictated by the U/D pin. Continue to pulse
INC (high to low) until the desired wiper position is
reached. On the last edge, hold the INC line low. With
the desired wiper position set, there are two ways to
proceed. One method terminates communication with-
out allowing the value of the current wiper position to
be written to the EEPROM. This is done by transitioning
the CS signal to the high state before bringing the INC
signal high. As long as the state of the CS pin is high
before the state of the INC pin goes high, the current
wiper setting is not written to EEPROM. Because the
current wiper setting was not stored to the NV memory,
the previously stored wiper setting, not the current
wiper setting, is loaded from memory if power is cycled
to the device
The other method is used to store a new wiper setting
in the EEPROM. This is done by bringing the state of
the INC pin high for a time of tIC before bringing the
state of the CS pin high. Once the states of both CS
and INC pins are high, the current wiper setting is
stored in EEPROM after a time of tWST. If power is
Nonvolatile, 32-Position Digital Potentiometer
6
_____________________________________________________________________
VCC
GND
CS
INC
U/D
CONTROL
LOGIC UNIT
NONVOLATILE
MEMORY
5-BIT
WIPER
SETTING
POS 31
POS 0
H
L
W
VCC
Figure 1. Block Diagram
CS
INC
U/D
tCI
tIL
tIH
tF
tIC
tWST
tCPH
tDI
tR
WIPER STORAGE
CONDITION
WIPER NON-STORAGE
CONDITION
WIPER POSITION
POSITION X
POSITION X + 1
POSITION X
tIW
tIK
POSITION X - 1
VIL
VIL
VIH
tCLP
Figure 2. Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| V24A48H300BF3 | CONVERTER MOD DC/DC 48V 300W |
| MS3450W28-9P | CONN RCPT 12POS WALL MNT W/PINS |
| VI-2W0-MY-S | CONVERTER MOD DC/DC 5V 50W |
| VI-2W0-MY-F4 | CONVERTER MOD DC/DC 5V 50W |
| VI-2W0-MY-F3 | CONVERTER MOD DC/DC 5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS4301Z-200 | 功能描述:数字电位计 IC RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| DS4302 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2-Wire, 5-Bit DAC with Three Digital Outputs |
| DS4302U-019 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2-Wire, 5-Bit DAC with Three Digital Outputs |
| DS4302U-020 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:2-Wire, 5-Bit DAC with Three Digital Outputs |
| DS4302Z-019 | 功能描述:IC DAC 5-BIT SGL 0-1.9V 8-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:3,000 系列:nanoDAC™ 设置时间:80µs 位数:18 数据接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:带卷 (TR) 输出数目和类型:1 电压，单极 采样率（每秒）:- 产品目录页面:784 (CN2011-ZH PDF) 配用:EVAL-AD5680EBZ-ND - BOARD EVAL FOR AD5680 其它名称:AD5680BRJZ-2REEL7TR |
发布紧急采购，3分钟左右您将得到回复。