- 您现在的位置：买卖IC网 > PDF目录10761 > DS4302Z-020 (Maxim Integrated Products)IC DAC 5-BIT SGL 0-2.0V 8-SOIC PDF资料下载
参数资料
| 型号： | DS4302Z-020 |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC DAC 5-BIT SGL 0-2.0V 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 97 |
| 设置时间： | 10µs |
| 位数： | 5 |
| 数据接口： | 串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 管件 |
| 输出数目和类型： | 1 电压，单极 |
| 采样率（每秒）： | * |
DS4302
Detailed Description
The DS4302 contains a 5-bit DAC and three programma-
ble digital outputs. The DAC setting and the pro-
grammed output levels are contained in a 1-byte data
word that defaults to 00h on power-up (see Figure 1 for
data byte configuration). The upper 5 MSbits of the byte
set the DAC and control the voltage produced on VOUT.
A setting of 1111 1XXX sets the minimum output voltage
from the DAC while a setting of 0000 0XXX sets the maxi-
mum output voltage from the DAC. The three LSbits of
the data byte control the three output pins, P0, P1, and
P2. Setting any of these control bits to a 0 pulls the corre-
sponding outputs low and setting the bits to a 1 pulls the
outputs high.
The DS4302 communicates through a 2-wire (SMBus-
compatible) digital interface and has a 2-wire address of
58h. Write and read operations are used to access the
DAC and output settings. Each operation begins with a
2-wire START condition, consists of three bytes, and
ends with a 2-wire STOP condition (see Figure 2). Using
the write operation, the 2-wire master can program the
5-bit DAC to adjust the voltage on VOUT and set the
level of the three output pins: P0, P1, and P2. The read
operation is used to recall the programmed settings.
2-Wire Definitions
The following terminology is commonly used to
describe 2-wire data transfers.
Master Device: The master device controls the slave
devices on the bus. The master device generates SCL
clock pulses, START, and STOP conditions.
Slave Devices: Slave devices send and receive data
at the master’s request.
Bus Idle or Not Busy: Time between STOP and START
conditions when both SDA and SCL are inactive and in
their logic-high states. When the bus is idle, it initiates a
low-power mode for slave devices.
START Condition: A START condition is generated by
the master to initiate a new data transfer with a slave.
Transitioning SDA from high to low while SCL remains
high generates a START condition. See Figure 3 for
applicable timing.
STOP Condition: A STOP condition is generated by the
master to end a data transfer with a slave. Transitioning
SDA from low to high while SCL remains high generates
a STOP condition. See Figure 3 for applicable timing.
Bit Write: Transitions of SDA must occur during the low
state of SCL. The data on SDA must remain valid and
unchanged during the entire high pulse of SCL plus the
setup and hold time requirements (see Figure 3). Data is
shifted into the device during the rising edge of the SCL.
2-Wire, 5-Bit DAC with Three Digital Outputs
6
_____________________________________________________________________
DATA BYTE
MSB
DAC VALUE
P0
P2
P1
Figure 1. Data Byte Configuration
Figure 2. 2-Wire Communication Examples
S
P
A
START
8-BITS ADDRESS OR DATA
STOP
ACK
WHITE BOXES INDICATE THE MASTER IS
CONTROLLING SDA
SHADED BOXES INDICATE THE SLAVE IS
CONTROLLING SDA
WRITE A SINGLE BYTE
AAh
READ A SINGLE BYTE
00h
59h
58h
COMMUNICATIONS KEY
S
XXX
X
XXX
X
010
1
100
0
A
DATA BYTE
A
P
NOTES:
1) ALL BYTES ARE SENT MOST SIGNIFICANT BIT FIRST.
2) THE FIRST BYTE SENT AFTER A START CONDITION IS
ALWAYS THE SLAVE ADDRESS FOLLOWED BY THE
READ/WRITE BIT.
0000
1111
S
01011001
A
DATA BYTE
A
P
00
0
0000
A
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J2P-MY-F1 | CONVERTER MOD DC/DC 13.8V 50W |
| B37872K5222K060 | CAP CER 2200PF 50V 10% X7R 1206 |
| B37872K5102K070 | CAP CER 1000PF 50V 10% X7R 1206 |
| B37872K5103K060 | CAP CER 10000PF 50V X7R 1206 |
| DS4302Z-019/T&R | IC DAC 5-BIT SGL 0-1.9V 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS4302Z-020/T&R | 制造商:Maxim Integrated Products 功能描述:IC DAC 5-BIT SGL 0-2.0V 8-SOIC |
| DS4302Z-020/T&R | 功能描述:IC DAC 5-BIT SGL 0-2.0V 8-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:3,000 系列:nanoDAC™ 设置时间:80µs 位数:18 数据接口:DSP，MICROWIRE?，QSPI?，串行，SPI? 转换器数目:1 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:带卷 (TR) 输出数目和类型:1 电压，单极 采样率（每秒）:- 产品目录页面:784 (CN2011-ZH PDF) 配用:EVAL-AD5680EBZ-ND - BOARD EVAL FOR AD5680 其它名称:AD5680BRJZ-2REEL7TR |
| DS4302Z-020+ | 功能描述:数模转换器- DAC 2-Wire 5-Bit w/3 Digital Outputs RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| DS4302Z-020+T&R | 制造商:Maxim Integrated Products 功能描述:DAC 1CH 5-BIT 8SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DAC 5-BIT SGL 0-2.0V 8-SOIC |
| DS4302Z-020+T&R | 功能描述:数模转换器- DAC 2-Wire 5-Bit w/3 Digital Outputs RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。