- 您现在的位置：买卖IC网 > PDF目录8541 > DS4402N+T&R/C (Maxim Integrated Products)IC DAC 2CH I2C ADJ 14-TDFN PDF资料下载
参数资料
| 型号： | DS4402N+T&R/C |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC DAC 2CH I2C ADJ 14-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 位数： | 5 |
| 数据接口： | I²C，串行 |
| 转换器数目： | 2 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-WFDFN 裸露焊盘 |
| 供应商设备封装： | 14-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | * |
| 其它名称： | 90-4402N+TRC |
Acknowledgement (ACK and NACK): An Acknowledge-
ment (ACK) or Not Acknowledge (NACK) is always the
ninth bit transmitted during a byte transfer. The device
receiving data (the master during a read or the slave
during a write operation) performs an ACK by transmit-
ting a zero during the ninth bit. A device performs a
NACK by transmitting a one during the ninth bit. Timing
for the ACK and NACK is identical to all other bit writes
(Figure 4). An ACK is the acknowledgment that the
device is properly receiving data. A NACK is used to
terminate a read sequence or as an indication that the
device is not receiving data.
Byte Write: A byte write consists of 8 bits of information
transferred from the master to the slave (most significant
bit first) plus a 1-bit acknowledgement from the slave to
the master. The 8 bits transmitted by the master are
done according to the bit-write definition, and the
acknowledgement is read using the bit-read definition.
Byte Read: A byte read is an 8-bit information transfer
from the slave to the master plus a 1-bit ACK or NACK
from the master to the slave. The 8 bits of information
that are transferred (most significant bit first) from the
slave to the master are read by the master using the bit
read definition above, and the master transmits an ACK
using the bit write definition to receive additional data
bytes. The master must NACK the last byte read to ter-
minated communication so the slave will return control
of SDA to the master.
Slave Address Byte: Each slave on the I2C bus
responds to a slave address byte sent immediately follow-
ing a START condition. The slave address byte contains
the slave address in the most significant 7 bits and the
R/W bit in the least significant bit. The DS4402/DS4404s’
slave address is determined by the state of the A0 and A1
address pins. Table 1 describes the addresses corre-
sponding to the state of A0 and A1.
When the R/W bit is 0 (such as in A0h), the master is
indicating it will write data to the slave. If R/W = 1 (A1h
in this case), the master is indicating it wants to read
from the slave. If an incorrect slave address is written,
the DS4402/DS4404 assume the master is communi-
cating with another I2C device and ignore the commu-
nication until the next START condition is sent.
Memory Address: During an I2C write operation, the
master must transmit a memory address to identify the
memory location where the slave is to store the data.
The memory address is always the second byte trans-
mitted during a write operation following the slave
address byte.
I2C Communication
Writing to a Slave: The master must generate a START
condition, write the slave address byte (R/W = 0), write
the memory address, write the byte of data, and gener-
ate a STOP condition. Remember that the master must
read the slave’s acknowledgement during all byte-write
operations.
Reading from a Slave: To read from the slave, the
master generates a START condition, writes the slave
address byte with R/W = 1, reads the data byte with a
NACK to indicate the end of the transfer, and generates
a STOP condition.
DS4402/DS4404
Two/Four-Channel, I2C Adjustable Current DAC
_____________________________________________________________________
7
SCL
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
SDA
STOP
START
REPEATED
START
tBUF
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
tHD:STA
tSP
tSU:STA
tHIGH
tR
tF
tLOW
Figure 3. I2C Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J1W-MW-S | CONVERTER MOD DC/DC 5.5V 100W |
| DS4422N+T&R | IC DAC 7BIT 2CH 5.5V 14-TDFN |
| VE-J1V-MW-S | CONVERTER MOD DC/DC 5.8V 100W |
| DS4422N+ | IC DAC 7BIT 2CH 5.5V 14-TDFN |
| VE-J10-MW-S | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS4402U+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| DS4402U+T&R | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| DS4404 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Two/Four-Channel, I2C Adjustable Current DAC |
| DS44049 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:SAFETY ISOLATING TRANSFORMER |
| DS4404FP000 | 制造商:Thomas & Betts 功能描述:400A,CON,3P4W,MG,404,3P480V |
发布紧急采购，3分钟左右您将得到回复。