- 您现在的位置：买卖IC网 > PDF目录1916 > DS4830T+ (Maxim Integrated Products)MCU 16B CTRL CALIBR MON 40-TQFN PDF资料下载
参数资料
| 型号： | DS4830T+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/30页 |
| 文件大小： | 0K |
| 描述： | MCU 16B CTRL CALIBR MON 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 系列： | MAXQ® |
| 核心处理器： | RISC |
| 芯体尺寸： | 16-位 |
| 速度： | 10MHz |
| 连通性： | 3 线，I²C，SPI |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 31 |
| 程序存储器容量： | 64KB（32K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 16 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 18x13b，D/A 8x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 其它名称： | 90-4830T+000 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
DS4830
Optical Microcontroller
25
Maxim Integrated
Temperature Measurement
The device provides an internal temperature sensor for
die temperature monitoring and two external remote
temperature-sensing channels. In external temperature
mode, current is forced into an external diode that is con-
nected between user-specified channel pins (GP8-GP9
or GP10-GP11). The diode temperature is obtained by
measuring the diode voltages at multiple bias currents.
These temperature channels can be enabled independ-
ently by setting the appropriate bit locations in the
TEMPCN register. Whenever a temperature conversion
is complete, the corresponding flag (INTDAI for internal
conversion, EX0DAI and EX1DAI for external conversion)
is set. These can be configured to cause an interrupt,
and can be cleared by software. The temperature meas-
urement resolution is 0.0625NC.
The device can use all the three modes explained above
simultaneously by using a time-slicing mechanism per-
formed by the internal controller. The ADC-related SFRs
are accessed in module 1 and module 2. For details
about this and the three blocks, refer to the ADC section
of the DS4830 User’s Guide.
Fast Comparator/Quick Trips
The device supports 8-bit quick-trip comparison function-
ality. The quick trips are required to continuously monitor
user-defined channels in a round-robin sequence.
The quick- trip controller allows the user control of the list
of channels to monitor. Each mode has a corresponding
choice of list of channels for the round robin.
In any mode of quick-trip operation, the quick trip (ana-
log) performs two comparisons on any selected channel.
1) Comparison with a high-threshold value.
2) Comparison with a low-threshold value.
Any comparison above the high-threshold value or below
the low-threshold value causes a bit to set in the cor-
responding register. This bit can be used to trigger an
interrupt. The threshold values are stored in 32 internal
register (16 for low-threshold settings and 16 for high-
threshold settings). The quick-trip controller provides the
appropriate sequence of clock and threshold values for
the quick trips. Because the quick trips and the ADC use
the same input pins, the controller ensures that no colli-
sion takes place.
The quick-trip-related SFRs are accessed in module
5. Refer to the quick trip section of the DS4830 User’s
Guide for more information.
I2C-Compatible Interface Modules
The device provides two independent I2C-compatible
interfaces: one is a master and the other is a slave.
I2C-Compatible Master Interface
The device features an internal I2C-compatible master
interface for communication with a wide variety of exter-
nal I2C devices. The I2C-compatible master bus is a
bidirectional bus using two bus lines: the serial-data line
(MSDA) and the serial-clock line (MSCL). For the I2C-
compatible master, the device has ownership of the I2C
bus and drives the clock and generates the START and
STOP signals. This allows the device to send data to a
slave or receive data from a slave.
When the I2C-compatible master interface is disabled,
MSDA and MSCL can be used as GPIO pins P1.0 and
P1.1, respectively, and accessed through PO1/PI1/PD1.
I2C-Compatible Slave Interface
The device also features an internal I2C-compatible slave
interface for communication with a host. Furthermore,
the device can be in-system programmed (bootloaded)
through the I2C-compatible slave interface. The two inter-
face signals used by the I2C slave interface are SCL and
SDA. For the I2C-compatible slave interface, the device
relies on an externally generated clock to drive SCL and
responds to data and commands only when requested
by the I2C master device. The I2C-compatible slave inter-
face is open drain and requires external pullup resistors.
SMBus Timeout
Both the I2C-compatible master and slave interfaces can
work in SMBusK-compatible mode for communication
with other SMBus devices. To achieve this, a 30ms timer
has been implemented on the I2C-compatible slave inter-
face to make the interface SMBus compatible. The pur-
pose of this timer is to issue a timeout interrupt and thus
the firmware can reset the I2C-compatible slave interface
when the SCL is held low for longer than 30ms. The timer
only starts when none of the following conditions is true:
1) The I2C-compatible slave interface is in the idle state
and there is no communications on the bus.
2) The I2C-compatible slave interface is not working in
SMBus-compatible mode.
SMBus is a trademark of Intel Corp.
相关PDF资料 |
PDF描述 |
|---|---|
| DS5000FP-16 | IC MODULE MICRO 16MHZ FLATPACK |
| DS5000T-32-16+ | IC MPU W/RTC 32KB 16MHZ 40-DIP |
| DS5001FP-16N | IC MPU 128K 16MHZ IND 80-TQFP |
| DS5002FMN-16 | IC MPU SECURE 16MHZ IND 80-TQFP |
| DS72612RP80FPV | IC SUPERH MPU ROMLESS 176LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS4830T+ | 功能描述:16位微控制器 - MCU Control Calibration & Opt Trans Mtr RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| DS4830T+T | 功能描述:16位微控制器 - MCU Control Calibration & Opt Trans Mtr RoHS:否 制造商:Texas Instruments 核心:RISC 处理器系列:MSP430FR572x 数据总线宽度:16 bit 最大时钟频率:24 MHz 程序存储器大小:8 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:2 V to 3.6 V 工作温度范围:- 40 C to + 85 C 封装 / 箱体:VQFN-40 安装风格:SMD/SMT |
| DS485 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Low Power RS-485/RS-422 Multipoint Transceiver |
| DS485M | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 数据速率:1136 Kbps 工作电源电压:3 V to 5.5 V 电源电流:5.9 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-28 封装:Tube |
| DS485M | 制造商:Texas Instruments 功能描述:RS485/422 LOW POWER TRNSCVR SOIC8 |
发布紧急采购，3分钟左右您将得到回复。