- 您现在的位置：买卖IC网 > PDF目录97869 > DS5000FP-16 (DALLAS SEMICONDUCTOR) 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | DS5000FP-16 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | QFP-80 |
| 文件页数： | 17/22页 |
| 文件大小： | 592K |
| 代理商： | DS5000FP-16 |
DS5000FP
4 of 22
PIN DESCRIPTION
PIN
DESCRIPTION
15, 17, 19,
21, 25, 27,
29, 31
P1.0 - P1.7. General purpose I/O Port 1.
34
RST - Active high reset input. A logic 1 applied to this pin will activate a reset state. This
pin is pulled down internally so this pin can be left unconnected if not used.
36
P3.0 RXD. General purpose I/O port pin 3.0. Also serves as the receive signal for the on
board UART. This pin should not be connected directly to a PC COM port.
38
P3.1 TXD. General purpose I/O port pin 3.1. Also serves as the transmit signal for the on
board UART. This pin should not be connected directly to a PC COM port.
39
P3.2 INT0 . General purpose I/O port pin 3.2. Also serves as the active low External
Interrupt 0.
40
P3.3 INT1 . General purpose I/O port pin 3.3. Also serves as the active low External
Interrupt 1.
41
P3.4 T0. General purpose I/O port pin 3.4. Also serves as the Timer 0 input.
44
P3.5 T1. General purpose I/O port pin 3.5. Also serves as the Timer 1 input.
45
P3.6 WR . General purpose I/O port pin. Also serves as the write strobe for Expanded bus
operation.
46
P3.7 RD . General purpose I/O port pin. Also serves as the read strobe for Expanded bus
operation.
47, 48
XTAL2, XTAL1. Used to connect an external crystal to the internal oscillator. XTAL1 is
the input to an inverting amplifier and XTAL2 is the output.
52, 53
GND. Logic ground.
49, 50, 51,
56, 58, 60,
64, 66
P2.0-P2.7. General purpose I/O Port 2. Also serves as the MSB of the Expanded Address
bus.
68
PSEN
- Program Store Enable. This active low signal is used to enable an external
program memory when using the Expanded bus. It is normally an output and should be
unconnected if not used. PSEN is also used to invoke the Bootstrap Loader. At this time,
PSEN
will be pulled down externally. This should only be done once the DS5000FP is
already in a reset state. The device that pulls down should be open drain since it must not
interfere with PSEN under normal operation.
70
ALE - Address Latch Enable. Used to de-multiplex the multiplexed Expanded
Address/Data bus on Port 0. This pin is normally connected to the clock input on a ’373
type transparent latch. When using a parallel programmer, this pin also assumes the
PROG
function for programming pulses.
73
EA
- External Access. This pin forces the DS5000FP to behave like an 8031. No internal
memory (or clock) will be available when this pin is at a logic low. Since this pin is pulled
down internally, it should be connected to +5V to use NV RAM. In a parallel
programmer, this pin also serves as VPP for super voltage pulses.
相关PDF资料 |
PDF描述 |
|---|---|
| DS5000T-32-16 | 8-BIT, 16 MHz, MICROCONTROLLER, DIP40 |
| DS5000T-8-16 | 8-BIT, 16 MHz, MICROCONTROLLER, DMA40 |
| DS5000T-8-8 | 8-BIT, 8 MHz, MICROCONTROLLER, PDIP40 |
| DS5000T-8-12 | 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40 |
| DS5001FP-16 | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS5000F-P16+ | 制造商:Maxim Integrated Products 功能描述:MICRO FLATPACK-16MHZ PB-FREE - Rail/Tube |
| DS5000FP-16+ | 功能描述:8位微控制器 -MCU Soft MCU Chip RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS5000T | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Soft Microcontroller Module |
| DS5000T/KIT | 功能描述:开发板和工具包 - 8051 RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| DS5000T0808 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:8-Bit Microcontroller |
发布紧急采购，3分钟左右您将得到回复。