- 您现在的位置：买卖IC网 > PDF目录97869 > DS5001FP-16 (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | DS5001FP-16 |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | Microcontroller |
| 英文描述： | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | MQFP-80 |
| 文件页数： | 3/27页 |
| 文件大小： | 934K |
| 代理商： | DS5001FP-16 |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
DS5001FP
11 of 27
Figure 6. DS5001FP CONNECTION TO 64k x 8 SRAM
POWER MANAGEMENT
The DS5001FP monitors VCC to provide power-fail reset, early warning power-fail interrupt, and switch
over to lithium backup. It uses an internal bandgap reference in determining the switch points. These are
called VPFW, VCCMIN, and VLI, respectively. When VCC drops below VPFW, the DS5001FP performs an
interrupt vector to location 2Bh if the power-fail warning was enabled. Full processor operation continues
regardless. When power falls further to VCCMIN, the DS5001FP invokes a reset state. No further code
execution is performed unless power rises back above VCCMIN. All decoded chip enables and the R/ W
signal go to an inactive (logic 1) state. VCC is still the power source at this time. When VCC drops further
to below VLI, internal circuitry switches to the lithium cell for power. The majority of internal circuits are
disabled and the remaining nonvolatile states are retained. Any devices connected VCCO are powered by
the lithium cell at this time. VCCO is at the lithium battery voltage minus approximately 0.45V. This drop
varies depending on the load. Low power SRAMs should be used for this reason. When using the
DS5001FP, the user must select the appropriate battery to match the RAM data retention current and the
desired backup lifetime. Note that the lithium cell is only loaded when VCC < VLI. The User’s Guide has
more information on this topic. The trip points VCCMIN and VPFW are listed in the Electrical Specifications
section.
相关PDF资料 |
PDF描述 |
|---|---|
| DS5002FP-16 | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
| DS5002FPM-16 | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
| DS75S | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS75U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75U-C12+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS5001FP-16+ | 功能描述:微处理器 - MPU Soft MCU Chip RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| DS5001FP-16N | 功能描述:微处理器 - MPU Soft MCU Chip RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| DS5001FP-16N+ | 功能描述:微处理器 - MPU Soft MCU Chip RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
| DS5001FPN08 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
| DS5001FPN12 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Microcontroller |
发布紧急采购，3分钟左右您将得到回复。