- 您现在的位置：买卖IC网 > PDF目录19486 > DS7505U+ (Maxim Integrated)IC DGTL THERMOMETER 2WIRE 8-USOP PDF资料下载
参数资料
| 型号： | DS7505U+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 9/14页 |
| 文件大小： | 197K |
| 描述： | IC DGTL THERMOMETER 2WIRE 8-USOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），比较器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 无 |
| 电源电压： | 1.7 V ~ 3.7 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-uMAX |
| 包装： | 管件 |
Register Pointer
The four DS7505 registers each have a unique 2-bit
pointer designation, which is defined in Table 5. When
reading from or writing to the DS7505, the user must
point the DS7505 to the register that is to be
accessed. When reading from the DS7505, once the
pointer is set, it remains pointed at the same register
until it is changed. For example, if the user desires to
perform consecutive reads from the temperature regis-
ter, then the pointer only has to be set to the tempera-
ture register one time, after which all reads are
automatically from the temperature register until the
pointer value is changed. When writing to the DS7505,
the pointer value must be refreshed each time a write is
performed, even if the same register is being written to
twice in a row.
At power-up, the pointer defaults to the temperature
register location. The temperature register can be read
immediately without resetting the pointer.
Changes to the pointer setting are accomplished as
described in the 2-Wire Serial Data Bus section.
2-Wire Serial Data Bus
The DS7505 communicates over a standard bidirection-
al 2-wire serial data bus that consists of a serial clock
(SCL) signal and serial data (SDA) signal. The DS7505
interfaces to the bus through the SCL input pin and
open-drain SDA I/O pin. All communication is MSB first.
The following terminology is used to describe 2-wire
communication:
Master Device: Microprocessor/microcontroller that
controls the slave devices on the bus. The master
device generates the SCL signal and START and STOP
conditions.
Slave: All devices on the bus other than the master.
The DS7505 always functions as a slave.
Bus Idle or Not Busy: Both SDA and SCL remain high.
SDA is held high by a pullup resistor when the bus is
idle, and SCL must either be forced high by the master
(if the SCL output is push-pull) or pulled high by a
pullup resistor (if the SCL output is open drain).
Transmitter: A device (master or slave) that is sending
data on the bus.
Receiver: A device (master or slave) that is receiving
data from the bus.
START Condition: Signal generated by the master to
indicate the beginning of a data transfer on the bus.
The master generates a START condition by pulling
SDA from high to low while SCL is high (see Figure 6).
A repeated START is sometimes used at the end of a
data transfer (instead of a STOP) to indicate that the
master performs another operation.
STOP Condition: Signal generated by the master to
indicate the end of a data transfer on the bus. The mas-
ter generates a STOP condition by transitioning SDA
from low to high while SCL is high (see Figure 6). After
the STOP is issued, the master releases the bus to its
idle state.
Acknowledge (ACK): When a device (either master or
slave) is acting as a receiver, it must generate an
acknowledge (ACK) on the SDA line after receiving
every byte of data. The receiving device performs an
ACK by pulling the SDA line low for an entire SCL peri-
od (see Figure 6). During the ACK clock cycle, the
transmitting device must release SDA. A variation on
the ACK signal is the not acknowledge (NACK). When
the master device is acting as a receiver, it uses a
NACK instead of an ACK after the last data byte to indi-
cate that it is finished receiving data. The master indi-
cates a NACK by leaving the SDA line high during the
ACK clock cycle.
Digital Thermometer and Thermostat
_______________________________________________________________________________________ 9
Table 3. Resolution Configuration
R1
R0
THERMOMETER
RESOLUTION (BITS)
MAX CONVERSION
TIME (ms)
0
0
9
25
0
1
10
50
1
0
11
100
1
1
12
200
Table 4. Fault Tolerance Configuration
F1
F0
CONSECUTIVE OUT-OF-LIMITS
CONVERSIONS TO TRIGGER O.S.
0
0
1
0
1
2
1
0
4
1
1
6
Table 5. Pointer Definition
REGISTER
P1
P0
Temperature
0
0
Configuration
0
1
T
HYST
1
0
T
OS
1
1
相关PDF资料 |
PDF描述 |
|---|---|
| TAJC686M016RNJ | CAP TANT 68UF 16V 20% 2312 |
| TPSC227M006R0100 | CAP TANT 220UF 6.3V 20% 2312 |
| RSM44DSEI-S13 | CONN EDGECARD 88POS .156 EXTEND |
| ADSP-BF512BSWZ-3 | IC DSP 16/32B 300MHZ LP 176LQFP |
| DRA73-471-R | INDUCTOR HI TEMP 470UH .326A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS7505U+ | 功能描述:板上安装温度传感器 Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS7505U+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL THERMOMETER AND THERMOSTAT 8USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DGTL THERMOMETER 2WIRE 8-USOP 制造商:Maxim Integrated Products 功能描述:Board Mount Temperature Sensors Thermometer & Thermostat |
| DS7505U+T&R | 功能描述:板上安装温度传感器 Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| DS7505UR | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Digital Thermometer and Thermostat |
| DS7505UT | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Digital Thermometer and Thermostat |
发布紧急采购，3分钟左右您将得到回复。