- 您现在的位置：买卖IC网 > PDF目录11790 > DS8023-RJX+ (Maxim Integrated Products)IC INTERFACE SMART CARD 28-TSSOP PDF资料下载
参数资料
| 型号： | DS8023-RJX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 17/17页 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 28-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 212 |
| 应用： | 智能卡 |
| 接口： | 模拟 |
| 电源电压： | 2.7 V ~ 6 V |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
| 产品目录页面： | 1399 (CN2011-ZH PDF) |
| 配用： | DS8023-KIT-ND - EVALUATION KIT FOR DS8023 |
DS8023
Smart Card Interface
9
Maxim Integrated
When a card is inserted into the reader (if PRES is
active), the host microcontroller can begin an activation
sequence (start a card session) by pulling CMDVCC
low. The following events form an activation sequence
(Figure 3):
1) Host: CMDVCC is pulled low.
2) DS8023: The internal oscillator changes to high
frequency (t0).
3) DS8023: The voltage generator is started simulta-
neously (t1 = t0).
4) DS8023: Raise VCC from 0 to 5V, 3V, or 1.8V with
a controlled slope (t2 = t1 + 1.5
× T). T is 64 times
the internal oscillator period (approximately 25s).
5) DS8023: I/O, AUX1, and AUX2 are enabled
(t3 = t1 + 4T).
6) DS8023: The CLK signal is applied to the C3 con-
tact (t4).
7) DS8023: RST is enabled simulataneously (t5 = t4 =
t11 + 7T).
An alternate sequence allows the application to control
when the clock is applied to the card.
1) Host: Set RSTIN high.
2) Host: Set CMDVCC low.
3) Host: Set RSTIN low between t3 and t5; CLK will now
start.
4) DS8023: RST stays low until t5, then RST becomes
the copy of RSTIN.
5) DS8023: RSTIN has no further effect on CLK after t5.
If the applied clock is not needed, set CMDVCC low
with RSTIN low. In this case, CLK starts at t3 (minimum
200ns after the transition on I/O, see Figure 4); after t5,
RSTIN can be set high to obtain an answer to request
(ATR) from an inserted smart card. Do not perform acti-
vation with RSTIN held permanently high.
ATR
CMDVCC
RST
RSTIN
CLK
VCC
I/O
I/OIN
t0 t1
t2
t3
t4
t5 = tACT
Figure 3. Activation Sequence Using RSTIN and CMDVCC
相关PDF资料 |
PDF描述 |
|---|---|
| VI-BTH-IX-F1 | CONVERTER MOD DC/DC 52V 75W |
| VI-BTH-IW-F3 | CONVERTER MOD DC/DC 52V 100W |
| NCN6000DTBR2 | IC INTERFACE SMART CARD 20TSSOP |
| DS8113-RNG+ | IC INTERFACE SMART CARD 28-SOIC |
| MAX1563ETC+ | IC CURR-LIM SW SNGL PROG 12-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS8023-RJX+ | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS8023-RJX+T&R | 制造商:Maxim Integrated Products 功能描述:DS8023 SMART CARD INT 28 TSSOP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC INTERFACE SMART CARD 28-TSSOP |
| DS8023-RJX+T&R | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS8023-RRX+ | 功能描述:接口 - 专用 Smart Card Interface RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| DS8023-RRX+T&R | 制造商:Maxim Integrated Products 功能描述:DS8023 SMART CARD INT 28 SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC INTERFACE SMART CARD 28-SOIC |
发布紧急采购，3分钟左右您将得到回复。