- 您现在的位置：买卖IC网 > PDF目录3787 > DS89C440-ENL (Maxim Integrated Products)IC MCU FLASH 32KB 33MHZ 44-TQFP PDF资料下载
参数资料
| 型号： | DS89C440-ENL |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/46页 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 32KB 33MHZ 44-TQFP |
| 标准包装： | 160 |
| 系列： | 89C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 33MHz |
| 连通性： | EBI/EMI，SIO，UART/USART |
| 外围设备： | 电源故障复位，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-TQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
DS89C430/DS89C450 Ultra-High-Speed Flash Microcontrollers
19 of 46
Table 2. SFR Reset Value (continued)
REGISTER
ADDRESS
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
TL2
CCh
0
TH2
CDh
0
PSW
D0h
0
FCNTL
D5h
1
0
1
0
FDATA
D6h
0
WDCON
D8h
0
Special
0
Special
0
Special
0
ACC
E0h
0
EIE
E8h
1
0
B
F0h
0
EIP1
F1h
1
0
EIP0
F8h
1
0
Note: Consult the Ultra-High-Speed Flash Microcontroller User’s Guide for more information about the bits marked “Special.”
Memory Organization
There are three distinct memory areas in the DS89C430: scratchpad registers, program memory, and data
memory. The registers are located on-chip but the program and data memory spaces can be on-chip, off-chip, or
both. The DS89C430/DS89C450 have 16kB/64kB of on-chip program memory, respectively, implemented in flash
memory and also have 1kB of on-chip data memory space that can be configured as program space using the
PRAME bit in the ROMSIZE feature. The DS89C430 uses a memory-addressing scheme that separates program
memory from data memory. The program and data segments can be overlapped since they are accessed in
different manners. If the maximum address of on-chip program or data memory is exceeded, the DS89C430
performs an external memory access using the expanded memory bus. The PSEN signal goes active low to serve
as a chip enable or output enable when performing a code fetch from external program memory. MOVX
instructions activate the RD or WR signal for external MOVX data memory access. The program memory
ROMSIZE feature allows software to dynamically configure the maximum address of on-chip program memory.
This allows the DS89C430 to act as a bootloader for an external memory. It also enables the use of the
overlapping external program spaces. The lower 128 bytes of on-chip flash memory—if ROMSIZE is greater than
0—are used to store reset and interrupt vectors. 256 bytes of on-chip RAM serve as a register area and program
stack, which are separated from the data memory.
Register Space
Registers are located in the 256 bytes of on-chip RAM labeled “internal registers” (Figure 6), which can be divided
into two sub areas of 128 bytes each. Separate classes of instructions are used to access the registers and the
program/data memory. The upper 128 bytes are overlapped with the 128 bytes of SFRs in the memory map.
Indirect addressing is used to access the upper 128 bytes of scratchpad RAM, while the SFR area is accessed
using direct addressing. The lower 128 bytes can be accessed using direct or indirect addressing.
There are four banks of eight working registers in the lower 128 bytes of scratchpad RAM. The working registers
are general-purpose RAM locations that can be addressed within the selected bank by any instructions that use
R0–R7. The register bank selection is controlled through the program status register in the SFR area. The contents
of the working registers can be used for indirect addressing of the upper 128 bytes of scratchpad RAM.
Individually addressable bits in the RAM and SFR areas support Boolean operations. In the scratchpad RAM area,
registers 20h–2Fh are bit addressable by software using Boolean operation instructions.
Another use of the scratchpad RAM area is for the stack. The stack pointer, contained in the SFRs, is used to
select storage locations for program variables and for return addresses of control operations.
相关PDF资料 |
PDF描述 |
|---|---|
| DS89C440-ENG | IC MCU FLASH 32KB 25MHZ 44-TQFP |
| MC9S08GT60ACBE | IC MCU 60K FLASH 4K RAM 42-SDIP |
| DS89C430-ENL | IC MCU FLASH 16KB 33MHZ 44-TQFP |
| MCF52221CAF66 | IC MCU 128K FLASH 66MHZ 100-LQFP |
| DS80C320-ECG/T&R | IC MCU HI SPEED 25MHZ 44-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS89C440-ENL+ | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| DS89C440-MNG | 功能描述:IC MCU FLASH 32KB 25MHZ 40-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:260 系列:73S12xx 核心处理器:80515 芯体尺寸:8-位 速度:24MHz 连通性:I²C，智能卡，UART/USART，USB 外围设备:LED，POR，WDT 输入/输出数:9 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-VFQFN 裸露焊盘 包装:管件 |
| DS89C440-MNL | 功能描述:IC MCU FLASH 32KB 33MHZ 40-DIP RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:260 系列:73S12xx 核心处理器:80515 芯体尺寸:8-位 速度:24MHz 连通性:I²C，智能卡，UART/USART，USB 外围设备:LED，POR，WDT 输入/输出数:9 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-VFQFN 裸露焊盘 包装:管件 |
| DS89C440-MNL+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS89C440-QNG | 功能描述:IC MCU FLASH 32KB 25MHZ 44-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:260 系列:73S12xx 核心处理器:80515 芯体尺寸:8-位 速度:24MHz 连通性:I²C，智能卡，UART/USART，USB 外围设备:LED，POR，WDT 输入/输出数:9 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-VFQFN 裸露焊盘 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。