- 您现在的位置：买卖IC网 > PDF目录3787 > DS89C440-QNG (Maxim Integrated Products)IC MCU FLASH 32KB 25MHZ 44-PLCC PDF资料下载
参数资料
| 型号： | DS89C440-QNG |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/46页 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH 32KB 25MHZ 44-PLCC |
| 标准包装： | 26 |
| 系列： | 89C |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 25MHz |
| 连通性： | EBI/EMI，SIO，UART/USART |
| 外围设备： | 电源故障复位，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 32KB（32K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振荡器型： | 外部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 44-LCC（J 形引线） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
DS89C430/DS89C450 Ultra-High-Speed Flash Microcontrollers
22 of 46
fetch that takes four clocks. Page mode 1 is the only external addressing mode where the CPU does not require
stalls for external memory access, but page misses result in reduced external access performance.
On-Chip Program Memory
The processor can fetch the entire on-chip program memory range automatically. By default, the reset routines and
all interrupt vectors are located in the lower 128 bytes of the on-chip program memory.
On-chip program memory is logically divided into pairs of 8kB, 16kB, or 32kB flash memory banks to support in-
application programming. The upper block of the on-chip program memory is designed to be programmed in-
application with the standard 5V VCC supply under the control of the user software or by using a built-in program
memory loader. It can also be programmed in standard flash or EPROM programmers. The DS89C430
incorporates a memory management unit (MMU) and other hardware to support any of the three programming
methods. The MMU controls program and data memory access, and provides sequencing and timing controls for
programming of the on-chip program memory. A separate security flash block supports a three-level lock, a 64-byte
encryption array, and other flash options.
Security Features
The DS89C430 incorporates a 64-byte encryption array, allowing the user to verify program codes while viewing
the data in encrypted form. The encryption array is implemented in a security flash memory block that has the
same electrical and timing characteristics as the on-chip program memory. Once the encryption array is
programmed to non-FFh, the data presented in the verify mode is encrypted. Each byte of data is XNORed with a
byte in the encryption array during verification.
A three-level lock restricts viewing of the internal program and data memory contents. By programming the three
lock bits, the user can select a level of security as specified in Table 3. The protection levels function differently
than those in a traditional 8051 microcontroller, and should not be used while executing external code.
Once a security level is selected and programmed, the setting of the lock bits remains. Only a mass erase can
erase these bits and allow reprogramming the security level to a less restricted protection.
Table 3. Flash Memory Lock Bits
LEVEL
LB1
LB2
LB3
PROTECTION
1
No program lock. Encrypted verify if encryption array is programmed. Do
not execute external program code while operating at this security level.
2
0
1
Prevent MOVC in external memory from reading program code in internal
memory. EA is sampled and latched on reset. Allow no further parallel or
program memory loader programming. Do not execute external program
code while operating at this security level.
3
X
0
1
Level 2 plus no verify operation. Also prevent MOVX in external memory
from reading internal SRAM. Do not execute external program code while
operating at this security level.
4
X
0
Level 3 plus no external execution.
The DS89C430 provides user-selectable options that must be set before beginning software execution. The option
control register uses flash bits rather than SFRs, and is individually erasable and programmable as a byte-wide
register. Bit 3 of this register is defined as the watchdog POR. Setting this bit to 1 disables the watchdog reset
function on power-up. Clearing this bit to 0 enables the watchdog reset function automatically. Other bits of this
register are undefined and are at logic 1 when read. The value of this register can be read at address FCh in
parallel programming mode or executing a verify-option-control register instruction in ROM loader mode or in-
application programming mode.
相关PDF资料 |
PDF描述 |
|---|---|
| DS89C440-MNL | IC MCU FLASH 32KB 33MHZ 40-DIP |
| DS89C440-MNG | IC MCU FLASH 32KB 25MHZ 40-DIP |
| DS89C440-ENL | IC MCU FLASH 32KB 33MHZ 44-TQFP |
| DS89C440-ENG | IC MCU FLASH 32KB 25MHZ 44-TQFP |
| MC9S08GT60ACBE | IC MCU 60K FLASH 4K RAM 42-SDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS89C440-QNL | 功能描述:IC MCU FLASH 32KB 33MHZ 44-PLCC RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:89C 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:260 系列:73S12xx 核心处理器:80515 芯体尺寸:8-位 速度:24MHz 连通性:I²C，智能卡，UART/USART，USB 外围设备:LED，POR，WDT 输入/输出数:9 程序存储器容量:64KB（64K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:2K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-VFQFN 裸露焊盘 包装:管件 |
| DS89C440-QNL+ | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Ultra-High-Speed Flash Microcontrollers |
| DS89C440-XXX | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Ultra-High-Speed Flash Microcontrollers |
| DS89C450 | 制造商:DALLAS 制造商全称:Dallas Semiconductor 功能描述:Ultra-High-Speed Flash Microcontrollers |
| DS89C450+ENG | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC 64KB FLASH 5V 44TQFP - Trays |
发布紧急采购，3分钟左右您将得到回复。