- 您现在的位置：买卖IC网 > PDF目录1917 > DSP56F802TA80E (Freescale Semiconductor)IC DSP 60MHZ 16KB FLASH 32-LQFP PDF资料下载
参数资料
| 型号： | DSP56F802TA80E |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 5/40页 |
| 文件大小： | 0K |
| 描述： | IC DSP 60MHZ 16KB FLASH 32-LQFP |
| 标准包装： | 250 |
| 系列： | 56F8xx |
| 核心处理器： | 56800 |
| 芯体尺寸： | 16-位 |
| 速度： | 80MHz |
| 连通性： | SCI |
| 外围设备： | POR，PWM，WDT |
| 输入/输出数： | 8 |
| 程序存储器容量： | 20KB（10K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 2K x 16 |
| 电压 - 电源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 数据转换器： | A/D 5x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-LQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
JTAG/OnCE
56F802 Technical Data, Rev. 9
Freescale Semiconductor
13
2.8 JTAG/OnCE
Part 3 Specifications
3.1 General Characteristics
The 56F802 is fabricated in high-density CMOS with 5-volt tolerant TTL-compatible digital inputs. The
term “5-volt tolerant” refers to the capability of an I/O pin, built on a 3.3V compatible process technology,
to withstand a voltage up to 5.5V without damaging the device. Many systems have a mixture of devices
designed for 3.3V and 5V power supplies. In such systems, a bus may carry both 3.3V and 5V- compatible
I/O voltage levels (a standard 3.3V I/O is designed to receive a maximum voltage of 3.3V
± 10% during
normal operation without causing damage). This 5V-tolerant capability therefore offers the power savings
of 3.3V I/O levels while being able to receive 5V levels without being damaged.
Absolute maximum ratings given in Table 3-1 are stress ratings only, and functional operation at the
maximum is not guaranteed. Stress beyond these ratings may affect device reliability or cause permanent
damage to the device.
Table 2-10 JTAG/On-Chip Emulation (OnCE) Signals
No. of
Pins
Signal
Name
Signal
Type
State During
Reset
Signal Description
1
TCK
Input
(Schmitt)
Input, pulled
low internally
Test Clock Input—This input pin provides a gated clock to synchronize the
test logic and shift serial data to the JTAG/OnCE port. The pin is connected
internally to a pull-down resistor.
1
TMS
Input
(Schmitt)
Input, pulled
high internally
Test Mode Select Input—This input pin is used to sequence the JTAG TAP
controller’s state machine. It is sampled on the rising edge of TCK and has an
on-chip pull-up resistor.
Note:
Always tie the TMS pin to VDD through a 2.2K resistor.
1
TDI
Input
(Schmitt)
Input, pulled
high internally
Test Data Input—This input pin provides a serial input data stream to the
JTAG/OnCE port. It is sampled on the rising edge of TCK and has an on-chip
pull-up resistor.
1
TDO
Output
Tri-stated
Test Data Output—This tri-statable output pin provides a serial output data
stream from the JTAG/OnCE port. It is driven in the Shift-IR and Shift-DR
controller states, and changes on the falling edge of TCK.
1
TRST
Input
(Schmitt)
Input, pulled
high internally
Test Reset—As an input, a low signal on this pin provides a reset signal to the
JTAG TAP controller. To ensure complete hardware reset, TRST should be
asserted at power-up and whenever RESET is asserted. The only exception
occurs in a debugging environment, since the OnCE/JTAG module is under
the control of the debugger. In this case it is not necessary to assert TRST
when asserting RESET. Outside of a debugging environment RESET should
be permanently asserted by grounding the signal, thus disabling the
OnCE/JTAG module on the device.
Note:
For normal operation, connect TRST directly to VSS. If the design is to be
used in a debugging environment, TRST may be tied to VSS through a 1K resistor.
相关PDF资料 |
PDF描述 |
|---|---|
| DSP56F803BU80E | IC DSP 80MHZ 64KB FLASH 100LQFP |
| DSP56F805FV80E | IC DSP 80MHZ 64KB FLASH 144LQFP |
| DSP56F807VF80E | IC DSP 80MHZ 60K FLASH 160-BGA |
| DSP56F826BU80 | IC DSP 80MHZ 64KB FLASH 100LQFP |
| DSP56F827FG80E | IC HYBRID CTRLR 16BIT 128-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DSP56F803 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Digital Switched-Mode Power Supply (SMPS) |
| DSP56F803BU80 | 功能描述:数字信号处理器和控制器 - DSP, DSC 80Mhz/ 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56F803BU80E | 功能描述:数字信号处理器和控制器 - DSP, DSC 80Mhz/40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT |
| DSP56F803BU80E | 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor |
| DSP56F803BU80E | 制造商:Freescale Semiconductor 功能描述:DSP LQFP100 3.6V |
发布紧急采购，3分钟左右您将得到回复。