参数资料
型号: DSPIC30F5016T-30I/PT
厂商: Microchip Technology
文件页数: 15/66页
文件大小: 0K
描述: IC DSPIC MCU/DSP 66K 80TQFP
产品培训模块: Asynchronous Stimulus
标准包装: 1,200
系列: dsPIC™ 30F
核心处理器: dsPIC
芯体尺寸: 16-位
速度: 30 MIP
连通性: CAN,I²C,SPI,UART/USART
外围设备: 高级欠压探测/复位,电机控制 PWM,QEI,POR,PWM,WDT
输入/输出数: 68
程序存储器容量: 66KB(22K x 24)
程序存储器类型: 闪存
EEPROM 大小: 1K x 8
RAM 容量: 2K x 8
电压 - 电源 (Vcc/Vdd): 2.5 V ~ 5.5 V
数据转换器: A/D 16x10b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 80-TQFP
包装: 带卷 (TR)
配用: AC164320-ND - MODULE SKT MPLAB PM3 80TQFP
AC30F007-ND - MODULE SKT FOR DSPIC30F 80TQFP
dsPIC30F Flash Programming Specification
DS70102K-page 22
2010 Microchip Technology Inc.
clocked out. The programmer can begin to clock out
the response 20
μsec after PGD is brought low, and it
must provide the necessary amount of clock pulses to
receive the entire response from the programming
executive.
Once the entire response is clocked out, the
programmer should terminate the clock on PGC until it
is time to send another command to the programming
executive. This protocol is illustrated in Figure 7-2.
7.3
SPI Rate
In Enhanced ICSP mode, the dsPIC30F operates from
the fast internal RC oscillator, which has a nominal
frequency of 7.37 MHz. This oscillator frequency yields
an effective system clock frequency of 1.84 MHz. Since
the SPI module operates in Slave mode, the
programmer must limit the SPI clock rate to a
frequency no greater than 1 MHz.
Note:
If the programmer provides the SPI with a
clock faster than 1 MHz, the behavior of
the programming executive will be
unpredictable.
7.4
Time Outs
The programming executive uses no Watchdog Timer
or time out for transmitting responses to the
programmer. If the programmer does not follow the flow
control mechanism using PGC, as described in
col”, it is possible that the programming executive will
behave unexpectedly while trying to send a response
to the programmer. Since the programming executive
has no time out, it is imperative that the programmer
correctly follow the described communication protocol.
As a safety measure, the programmer should use the
command time outs identified in Table 8-1. If the
command time out expires, the programmer should
reset
the
programming
executive
and
start
programming the device again.
FIGURE 7-2:
PROGRAMMING EXECUTIVE – PROGRAMMER COMMUNICATION PROTOCOL
1
2
15 16
1
2
15 16
PGC
PGD
PGC = Input
PGC = Input (Idle)
Host Transmits
Last Command Word
PGD = Input
PGD = Output
P8
1
2
15 16
MSB X X X LSB
1
0
P9b
P10
PGC = Input
PGD = Output
P9a
Programming Executive
Processes Command
Host Clocks Out Response
P11
相关PDF资料
PDF描述
PIC16F877-10E/P IC MCU FLASH 8KX14 EE 40DIP
GCJ31CR71E475KA12L CAP CER 4.7UF 25V 10% X7R 1206
PIC16LC64A-04I/PQ IC MCU OTP 2KX14 PWM 44-MQFP
DSPIC30F5015T-20E/PT IC DSPIC MCU/DSP 66K 64TQFP
PIC16LF874-04/L IC MCU FLASH 4KX14 EE A/D 44PLCC
相关代理商/技术参数
参数描述
DSPIC30F6010-20E/PF 功能描述:数字信号处理器和控制器 - DSP, DSC 30MHz 66KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F6010-20I/PF 功能描述:数字信号处理器和控制器 - DSP, DSC 20MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F6010-20I/PF 制造商:Microchip Technology Inc 功能描述:16BIT 20MIPS DSPIC SMD 30F6010
DSPIC30F6010-30I/PF 功能描述:数字信号处理器和控制器 - DSP, DSC 30MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F6010-30I/PF 制造商:Microchip Technology Inc 功能描述:16BIT 30MIPS DSPIC SMD 30F6010