收藏本站
参数资料
型号： DSPIC30F6011A-20I/PT
厂商： Microchip Technology
文件页数： 10/66页
文件大小： 0K
描述： IC DSPIC MCU/DSP 132K 64TQFP
标准包装： 160
系列： dsPIC™ 30F
核心处理器： dsPIC
芯体尺寸： 16-位
速度： 20 MIPS
连通性： CAN，I²C，SPI，UART/USART
外围设备： 欠压检测/复位，LVD，POR，PWM，WDT
输入/输出数： 52
程序存储器容量： 132KB（44K x 24）
程序存储器类型： 闪存
EEPROM 大小： 2K x 8
RAM 容量： 6K x 8
电压 - 电源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
数据转换器： A/D 16x12b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 64-TQFP
包装： 托盘
其它名称： DSPIC30F6011A20IP
dsPIC30F Flash Programming Specification
DS70102K-page 18
2010 Microchip Technology Inc.
5.7.2
PROGRAMMING METHODOLOGY
System operation Configuration bits are inherently
different than all other memory cells. Unlike code
memory,
data
EEPROM
and
code-protect
Configuration bits, the system operation bits cannot be
erased. If the chip is erased with the ERASEB
command, the system-operation bits retain their
previous value. Consequently, you should make no
assumption about the value of the system operation
bits. They should always be programmed to their
desired setting.
Configuration bits are programmed as a single word at
a time using the PROGC command. The PROGC
command specifies the configuration data and
Configuration register address. When Configuration
bits are programmed, any unimplemented bits must be
programmed with a ‘0’, and any reserved bits must be
programmed with a ‘1’.
Four PROGC commands are required to program all the
Configuration bits. Figure 5-5 illustrates the flowchart of
Configuration bit programming.
Note:
If the General Code Segment Code
Protect (GCP) bit is programmed to ‘0’,
code memory is code-protected and can-
not be read. Code memory must
be verified before enabling read protec-
tion. See Section 5.7.4 “Code-Protect
Configuration Bits” for more information
about code-protect Configuration bits.
5.7.3
PROGRAMMING VERIFICATION
Once the Configuration bits are programmed, the
contents of memory should be verified to ensure that
the programming was successful. Verification requires
the Configuration bits to be read back and compared
against the copy held in the programmer’s buffer. The
READD command reads back the programmed
Configuration
bits
and
verifies
whether
the
programming was successful.
Any unimplemented Configuration bits are read-only
and read as ‘0’.
5.7.4
CODE-PROTECT CONFIGURATION
BITS
The FBS, FSS and FGS Configuration registers are
special Configuration registers that control the size and
level of code protection for the Boot Segment, Secure
Segment and General Segment, respectively. For each
segment, two main forms of code protection are
provided. One form prevents code memory from being
written (write protection), while the other prevents code
memory from being read (read protection).
The BWRP, SWRP and GWRP bits control write
protection; and BSS<2:0>, SSS<2:0> and GSS<1:0>
bits control read protection. The Chip Erase ERASEB
command sets all the code protection bits to ‘1’, which
allows the device to be programmed.
When write protection is enabled, any programming
operation to code memory will fail. When read
protection is enabled, any read from code memory will
cause a ‘0x0’ to be read, regardless of the actual
contents of code memory. Since the programming
executive always verifies what it programs, attempting
to program code memory with read protection enabled
will also result in failure.
It is imperative that all code protection bits are ‘1’ while
the device is being programmed and verified. Only after
the device is programmed and verified should any of
the above bits be programmed to ‘0’ (see Section 5.7
“Configuration Bits Programming”).
In addition to code memory protection, parts of data
EEPROM and/or data RAM can be configured to be
accessible only by code resident in the Boot Segment
and/or Secure Segment. The sizes of these “reserved”
sections are user-configurable, using the EBS,
RBS<1:0>, ESS<1:0> and RSS<1:0> bits.
Note 1: All bits in the FBS, FSS and FGS
Configuration registers can only be
programmed to a value of ‘0’. ERASEB is
the only way to reprogram code-protect
bits from ON (‘0’) to OFF (‘1’).
2: If any of the code-protect bits in FBS,
FSS, or FGS are clear, the entire device
must be erased before it can be
reprogrammed.
相关PDF资料
PDF描述
DSPIC30F6010A-20I/PT IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F5016-20I/PT IC DSPIC MCU/DSP 66K 80TQFP
PIC16LF1526-I/PT MCU PIC 14KB FLASH 64TQFP
PIC16LF724-I/P IC PIC MCU FLASH 7KB 40-PDIP
DSPIC30F2010T-20I/SOG IC DSPIC MCU/DSP 12K 28SOIC
相关代理商/技术参数
参数描述
dsPIC30F6011A-30I/PF 功能描述:数字信号处理器和控制器 - DSP, DSC 30MIPS 132 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F6011A-30I/PF 制造商:Microchip Technology Inc 功能描述:IC DSC 16BIT 132KB 40MHZ 5.5V TQFP-64
dsPIC30F6011A-30I/PT 功能描述:数字信号处理器和控制器 - DSP, DSC 30MIPS 132 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
dsPIC30F6011AT-20E/PT 功能描述:数字信号处理器和控制器 - DSP, DSC 20MIPS 132 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 数据总线宽度:16 bit 程序存储器大小:16 KB 数据 RAM 大小:2 KB 最大时钟频率:40 MHz 可编程输入/输出端数量:35 定时器数量:3 设备每秒兆指令数:50 MIPs 工作电源电压:3.3 V 最大工作温度:+ 85 C 封装 / 箱体:TQFP-44 安装风格:SMD/SMT
DSPIC30F6011AT-20I/PT 功能描述:IC DSPIC MCU/DSP 132K 64TQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:dsPIC™ 30F 产品培训模块:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 标准包装:22 系列:PIC® XLP™ 18F 核心处理器:PIC 芯体尺寸:8-位 速度:48MHz 连通性:I²C，SPI，UART/USART，USB 外围设备:欠压检测/复位，POR，PWM，WDT 输入/输出数:14 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:20-DIP（0.300"，7.62mm） 包装:管件 产品目录页面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*