- 您现在的位置：买卖IC网 > PDF目录93281 > E110 Test Methods for 10Base-T Modules PDF资料下载
参数资料
| 型号： | E110 |
| 英文描述： | Test Methods for 10Base-T Modules |
| 中文描述： | 试验方法10Base - T的模块 |
| 文件页数： | 2/4页 |
| 文件大小： | 56K |
| 代理商： | E110 |
TEST METHODS FOR PULSE
10BASE-T MODULES
Application Note
12220 WORLD TRADE DRIVE, SAN DIEGO, CALIFORNIA 92128 TEL 619-674-8100 FAX 619-674-8262 http://www.pulseeng.com
E110.A (5/97)
Figure 1
HP3577
NETWORK
ANALYZER
OR EQUIVALENT
NORTH HILLS 0300BB
OR EQUIVALENT
NORTH HILLS 0300BB
OR EQUIVALENT
LP
XFMR
CMI
XFMR
CMI
1
2
3
4
5
6
7
14
13
12
11
10
9
8
PORT A
PORT B
50
100
50
100
RDM
RDP
TDP
TDM
TPR+
TPR-
TPX1+
TPX1-
TPX2+
TPX2-
GND
Return Loss
Nominal input impedance is 100
; however, the IEEE 802.3i Standard calls for 96 ±20%. The
measured return loss shall be a minimum of 15 dB at impedance extremes. Return loss is an
actual measurement of the mismatches in the module. If each element were a pure and precise
100
, there would be no reflection or return; however, realistically, some mismatch does occur.
In order to meet 15 dB at impedance extremes, a typical device should exhibit at least 20 dB at a
nominal impedance of 100
.
Figure 2, on the next page, shows a typical test set-up for Return Loss. The following is the test
procedure:
1. Calibrate the network analyzer in the S11 mode.
2. Short pins 13 and 14. Do a short.
3. Leave pins 13 and 14 open. Do an open.
4. Connect a 100
resistor across pins 13 and 14. Do a load measure.
5. Filter must be terminated in the appropriate test impedance with 100
termination.
6. Measure the Return Loss at 5 MHz to 10 MHz.
相关PDF资料 |
PDF描述 |
|---|---|
| E111-SERIES | Peripheral IC |
| E112-SERIES | Peripheral IC |
| E121-SERIES | Peripheral IC |
| E122-SERIES | Peripheral IC |
| E123-SERIES | Peripheral IC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| E110.000 | 功能描述:折皱器 Ferrule Crimper 26-10 AWG RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| E110.005 | 功能描述:折皱器 UNIV FERRULE CRIMPER 20-8 AWG 0.5-10 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| E110.010 | 功能描述:折皱器 FERRULE CRIMPER 8-6AWG RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| E110.015 | 功能描述:折皱器 FERRULE CRIMPER 4-2AWG 25-35 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| E110.020 | 功能描述:折皱器 FERRULE CRIMPER 1 AWG 50 RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
发布紧急采购，3分钟左右您将得到回复。