参数资料
型号: E5561
英文描述: e5561 Advance Information [Updated 4/03. 26 Pages] Read/Write transponder IC for contactless RF identification for highly sophisticated security applications.
中文描述: e5561推进信息[更新4 / 03。 26页]读/写非接触式射频转发器的高度复杂的安全应用识别芯片。
文件页数: 10/26页
文件大小: 410K
代理商: E5561
18
e5561
4699A–RFID–04/03
For programming or direct-access mode, the password function has to be disabled by
receiving the password.
If this function is enabled, the customer configuration can only be changed by an autho-
rized person using the correct password of the e5561.
During password mode, the e5561 monitors several fault and protection mechanism. If a
fault or a protection violation is detected, the e5561 enters ID mode.
Error Handling
Several error conditions can be detected to ensure that only valid operations affect the
e5561.
Errors while Writing Data There are four detectable errors possible during writing data to the e5561:
Field gap was not detected
Wrong number of field clocks between two gaps, e.g., 37 FCs
The OPcode is not valid (11)
The number of bits received is incorrect; valid bit counts are:
programming mode: 38 bits
direct-access mode: 6 bits
crypto mode: 66 bits
stop mode: 2 bits
If any of these four conditions is detected, the e5561 stops writing and enters ID mode.
This can easily be analyzed using the damping which is usually on during writing. It
changes according to the selected modulation scheme in ID mode.
Errors During Programming
Mode
If the writing sequence has been transmitted successfully, there are three errors that
may prevent the e5561 from programming the data to the EEPROM:
The programming voltage VPP is too low, i.e., the field strength is not high enough
The lock-bit of the adressed block is set
The password function is enabled
In these cases, the procedure stops immediately after the error has been detected and
the IC reverts to ID mode.
Errors During Direct-access
Mode
In addition to the possible errors mentioned before, two errors may occur in direct-
access mode:
The lock-bit of the addressed block 5 to 8 is set
The password function is enabled
In these cases, the IC enters ID mode after the end of the writing sequence.
Errors During Crypto Mode
In crypto mode, ONE error mechanism is active, that may prevent the e5561 from send-
ing the correct response:
Error during the crypto writing sequence
The e5561 will enter ID mode immediately if an error in the writing sequence is detected.
If the password function is enabled, the e5561 enters ID mode after having completed
the writing sequence.
相关PDF资料
PDF描述
E629-EDGE629 1 GHz Timing Deskew and Quad Fanout Element
E6420-EDGE6420 Per-Pin Electronics Companion DAC
E646-EDGE646 Pin Electronics Driver. Window Comparator. and Switch Matrix
E647-EDGE647 Pin Electronics Driver. Window Comparator. and Switch Matrix
E649-EDGE649 Octal Pin Electronics Driver / Receiver
相关代理商/技术参数
参数描述
E5561_06 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Standard Read/Write Crypto Identification IC
e5561A-DOW 功能描述:射频无线杂项 Encryption w/unique options RoHS:否 制造商:Texas Instruments 工作频率:112 kHz to 205 kHz 电源电压-最大:3.6 V 电源电压-最小:3 V 电源电流:8 mA 最大功率耗散: 工作温度范围:- 40 C to + 110 C 封装 / 箱体:VQFN-48 封装:Reel
E5562-00L022-L 功能描述:以太网和电信连接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级:
E5562-60L121-L 功能描述:以太网和电信连接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级:
E5562-60LU22-L 功能描述:以太网和电信连接器 RJ11 6P2C SIDE ENTRY RoHS:否 制造商:Pulse 产品:Modular Jacks 性能类别: USOC 代码:RJ45 位置/触点数量: 安装风格:Through Hole 端口数量:1 x 1 型式:Female 屏蔽: 电流额定值: 电压额定值: 触点电镀: 外壳材料:Thermoplastic IP 等级: