参数资料
型号: E647-EDGE647
英文描述: Pin Electronics Driver. Window Comparator. and Switch Matrix
中文描述: 引脚电子驱动程序。窗口比较器。和开关矩阵
文件页数: 8/13页
文件大小: 138K
代理商: E647-EDGE647
4
2000 Semtech Corp.
www.semtech.com
EDGE HIGH-PERFORMANCE PRODUCTS
Edge647
the DUT. In this environment, the driver can withstand a
short to any legal DUT voltage for an indefinite period.
In a low impedance application with no additional output
series resistance, care must be exercised and systems
should be designed to check for this condition and tristate
the driver if a short is detected.
The driver does NOT have on-chip short circuit protection
or limitation circuitry.
VBB
VBB is an analog input which establishes the threshold
for all single ended digital input signals.
If SW0 EN*,
SW1 EN*, or SW2 EN* are more positive than VBB, these
inputs are a digital “1".
Conversely, if they are more
negative than VBB, they are a “0".
All digital inputs are wide voltage comparator inputs, so
they are technology independent.
By establishing the
appropriate VBB level for the switch control inputs, and
the appropriate differential input levels for the driver digital
control inputs, the Edge647 may be driven by TTL, ECL,
CMOS, or any custom level circuitry.
Figure 1. Driver Digital Inputs
Figure 2. Driver Differential Digital Inputs
Circuit Description
Driver Description
The Edge647 driver supports three distinct programmable
driver levels; high, low, and termination,
and high
impedance. There are no restrictions between any of these
three levels in that all three may vary independently over
the entire operating voltage range between VCC and VEE.
The DVR EN*, DATA, and VTT EN pins are digital inputs
that control the driver (see Table 1). With DVR EN* low,
DATA determines whether the driver will force VH or VL at
DOUT. With DVR EN* high, VTT EN* controls whether the
driver goes into high impedance or drives VTT.
Table 1. Driver Truth Table
VH, VL, and VTT
VH, VL, and VTT define the logical “1”, “0”, and
“termination” levels of the driver and can be adjusted
anywhere over the range spanned by VCC to VEE. There
is no restriction between VH, VL, and VTT, in that they can
all vary independently over the entire voltage range
determined by the power supply levels.
The VH, VL, and VTT inputs are unbuffered in that they
also provide the driver output current, so the sources of
these voltages must have ample current drive capability.
While VTT is referred to as the termination voltage, it may
also be used as a very high “programming” level on many
memory devices.
Driver Output Protection
The Edge647 is designed to operate in a functional testing
environment where a controlled impedance (typically 50
) is maintained between the pin electronics and the DUT.
In general, there will be an external resistor at the driver
output which series terminates the transmission line to
*
N
E
R
V
DN
E
T
VA
T
A
DT
U
O
D
10
X
Z
i
H
11
X
T
V
0X0
L
V
0X1
H
V
SW0 EN*
SW1 EN*
SW2 EN*
VBB
DATA
DATA*
DVR EN*
DVR EN
VTT EN
VTT EN*
相关PDF资料
PDF描述
E649-EDGE649 Octal Pin Electronics Driver / Receiver
E670-EDGE670 500 MHz Window Comparator
E672-EDGE672 500 MHz Pin Electronics Window Comparator and Load
E692-EDGE692 200 MHz Monolithic Dual Pin Electronics Driver
E693-EDGE693 500 MHz Monolithic Dual Pin Electronics Driver
相关代理商/技术参数
参数描述
E64808-000 制造商:TE Connectivity 功能描述:VARISTOR 39V 10MM RADIAL T/R 制造商:TE Connectivity 功能描述:VARISTOR 39V 3.5KA DISC 10MM
E64809-000 制造商:TE Connectivity 功能描述:CBL 3CNDCTR 20AWG NKL PLTD CPPR WH 600V - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:55PC1233-20-9/93/96-9
E6485 功能描述:BOARD EVALUATION FOR QT60485 制造商:microchip technology 系列:Quantum 零件状态:停產 传感器类型:- 感应范围:- 接口:- 灵敏度:- 电压 - 电源:- 嵌入式:- 所含物品:板 使用的 IC/零件:- 标准包装:1
E6486 功能描述:触摸传感器开发工具 Eval Board for QT60326/486 Series RoHS:否 制造商:Cypress Semiconductor 工具用于评估: 接口类型: 工作电压: 最大工作温度:
E6486 制造商:Quantum Corp 功能描述:KITTOUCH SENSOR 48 CH EVAL