- 您现在的位置：买卖IC网 > PDF目录97873 > E649-EDGE649 Octal Pin Electronics Driver / Receiver PDF资料下载
参数资料
| 型号： | E649-EDGE649 |
| 英文描述： | Octal Pin Electronics Driver / Receiver |
| 中文描述： | 八路引脚电子驱动器/接收器 |
| 文件页数： | 13/16页 |
| 文件大小： | 150K |
| 代理商： | E649-EDGE649 |
6
Revision 5 / October 21, 2002
www .semtech.com
TEST AND MEASUREMENT PRODUCTS
Edge649
Application Infor mation
Power Supplies
The Edge649 uses three power supplies: VDD, VCC and
VEE. VDD is the digital supply for all of the data inputs
and outputs. VCC and VEE are the analog power supplies
for the Edge649 drivers and comparators. In order to
protect the Edge649 and avoid damaging it, the following
power supply requirements must be satisifed at all times:
VEE
≤ GND ≤ VDD ≤ VCC
Also,
VEE
≤ All Inputs ≤ VCC at all times
The three-diode configuration shown in Figure 5, used
on a once-per-board basis, insures power supply
sequence and fault tolerance.
Figure 5. Power Supply Protection Scheme
The sequence below can be used as a guideline with the
Edge649:
Power-On Sequencing
Power-Off Sequencing
1. VCC (substrate)
1. Inputs
2. VEE
2. VDD
3. VDD
3. VEE
4. Inputs
4. VCC
Power Supplies Decoupling
VDD, which provides the digital power, should be
decoupled to GND with a .1
F chip capacitor in parallel
with a .001
F chip capacitor. The bypass capacitors
should be as close to the device as possible. Power and
ground planes are recommended to provide a low
inductance return path.
VCC and VEE, which power the DUT drivers and receivers,
should also be decoupled to GND with a .1
F chip
capacitor in parallel with a .001
F chip capacitor. A
VCC and VEE plane, or at least a solid power bus, is
recommended for optimal performance.
VHIGH and VLOW Decoupling
As the VHIGH and VLOW inputs are unbuffered and must
supply the driver output current, decoupling capacitors
for these inputs are recommended in proportion to the
amount of output current the application requires
Expanding the Common Mode Range
Although the Edge649 can drive and receive 11V swings,
these 11 V signals can be adjusted over an 14V range.
By using programmable regulators V1 and V2 for the
VCC and VEE supplies (feasible because these two
analog power supplies do not supply driver output
current), the Edge649 I/O range can be optimized for a
variety of applications (see Figure 6).
Figure 6.
There are three rules which govern the supplies V1 and
V2:
1)
VDD + 1.5V
≤ V1 ≤ +11V
2)
–3V
≤ V2 ≤ 0V
3)
(V1 – V2)
≤ 11V
VCC
VDD
VEE
1N5820 or
Equivalent
V1
Edge 649
V2
VCC
VDD
相关PDF资料 |
PDF描述 |
|---|---|
| E670-EDGE670 | 500 MHz Window Comparator |
| E672-EDGE672 | 500 MHz Pin Electronics Window Comparator and Load |
| E692-EDGE692 | 200 MHz Monolithic Dual Pin Electronics Driver |
| E693-EDGE693 | 500 MHz Monolithic Dual Pin Electronics Driver |
| E710-EDGE710 | 500 MHz Pin Electronics Driver. Window Comparator. and Load |
相关代理商/技术参数 |
参数描述 |
|---|---|
| E-64-C | 功能描述:TOUCHSCREEN 6.4" RS-232 RoHS:是 类别:光电元件 >> 触摸屏覆盖层 系列:E 标准包装:25 系列:- 长度:15" (381mm) 宽:0.13"（3.18mm） 高度:12.03"（305.6mm） 接口:需要控制器 类型:电阻 屏幕对角尺寸:19.2"（487.68mm） 相关产品:BER244-ND - POWER SUPPLY FOR TOUCH SCRN MODBER243-ND - CABLE USB FOR TOUCH SCREEN MODBER242-ND - CABLE RS232 FOR TOUCH SCREEN MODBER241-ND - CONTROLLER TOUCH SCRN USB RS232 其它名称:BER240 |
| E64CAT2T | 制造商:Eaton Corporation 功能描述:SELF CONTAINED PHOTOELECT VEND |
| E64CAT5T | 制造商:Eaton Corporation 功能描述:PHOTO SENSOR POLARIZED REFLEX TIME DELAY |
| E64KR54 | 制造商:Eaton Corporation 功能描述:RECTANGULAR REFLECTOR |
| E-64-U | 功能描述:TOUCHSCREEN 6.4" USB RoHS:是 类别:光电元件 >> 触摸屏覆盖层 系列:E 标准包装:25 系列:- 长度:15" (381mm) 宽:0.13"（3.18mm） 高度:12.03"（305.6mm） 接口:需要控制器 类型:电阻 屏幕对角尺寸:19.2"（487.68mm） 相关产品:BER244-ND - POWER SUPPLY FOR TOUCH SCRN MODBER243-ND - CABLE USB FOR TOUCH SCREEN MODBER242-ND - CABLE RS232 FOR TOUCH SCREEN MODBER241-ND - CONTROLLER TOUCH SCRN USB RS232 其它名称:BER240 |
发布紧急采购，3分钟左右您将得到回复。