- 您现在的位置：买卖IC网 > PDF目录17024 > EA-QSB-002 (Embedded Artists)BOARD QUICK START LPC2106 PDF资料下载
参数资料
| 型号： | EA-QSB-002 |
| 厂商： | Embedded Artists |
| 文件页数： | 22/41页 |
| 文件大小： | 0K |
| 描述： | BOARD QUICK START LPC2106 |
| 标准包装： | 1 |
| 系列： | LPC2100 |
| 类型： | MCU |
| 适用于相关产品： | LPC2106 |
| 所含物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
LPC2104_2105_2106_7
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 07 — 20 June 2008
29 of 41
NXP Semiconductors
LPC2104/2105/2106
Single-chip 32-bit microcontrollers
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (+25
°C), nominal supply voltages.
[2]
Internal rail.
[3]
External rail.
[4]
Including voltage on outputs in 3-state mode.
[5]
VDD(3V3) supply voltages must be present.
[6]
3-state outputs go into 3-state mode when VDD(3V3) is grounded.
[7]
Accounts for 100 mV voltage drop in all supply lines.
[8]
Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[9]
Minimum condition for VI = 4.5 V, maximum condition for VI = 5.5 V.
[10] Applies to P0[31:22].
[11] SPI is enabled and SSP is disabled in the PCONP register (
see LPC2104/2105/2106 user manual).
[12] To VSS.
8.1 Power consumption measurements for LPC2104/2105/2106/01
The power consumption measurements represent typical values for the given conditions.
The peripherals were enabled through the PCONP register, but for these measurements
the peripherals were not congured to run. Power measurements with all peripherals
enabled were performed with the SPI enabled and the SSP disabled. Peripherals were
disabled through the PCONP register. Refer to the
LPC2104/2105/2106 User Manual for a
description of the PCONP register.
Oscillator pins
Vi(XTAL1)
input voltage on pin XTAL1
0
-
1.8
V
Vo(XTAL2)
output voltage on pin
XTAL2
0
-
1.8
V
Table 9.
Static characteristics …continued
Tamb =0 °C to +70 °C for commercial applications, unless otherwise specied.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
Test conditions: Active mode entered executing code from on-chip ash; PCLK = CCLK
4;
Tamb =25 °C; core voltage 1.8 V.
Fig 5.
Typical LPC2104/2105/2106/01 IDD(act) measured at different frequencies
frequency (MHz)
12
60
44
28
002aad709
20
40
60
IDD(act)
(mA)
0
all peripherals enabled
all peripherals disabled
相关PDF资料 |
PDF描述 |
|---|---|
| GBA32DRMI | CONN EDGECARD 64POS .125 SQ WW |
| 0210490229 | CABLE JUMPER 1.25MM .254M 16POS |
| EA-EDU-009 | BOARD EDUCATION LPC2103 |
| 0210490228 | CABLE JUMPER 1.25MM .229M 16POS |
| 0210490227 | CABLE JUMPER 1.25MM .229M 16POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EA-QSB-003 | 功能描述:开发板和工具包 - ARM LPC2129 CAN QUICKSTART BRD RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| EA-QSB-010 | 功能描述:开发板和工具包 - ARM LPC2148 USB QUICKSTART BRD RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| EA-QSB-012 | 功能描述:开发板和工具包 - ARM QUICK START BOARD LPC1343 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| EA-QSB-015 | 功能描述:开发板和工具包 - ARM QUICK START BOARD LPC11U35 RoHS:否 制造商:Arduino 产品:Development Boards 工具用于评估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口类型:DAC, ICSP, JTAG, UART, USB 工作电源电压:3.3 V |
| EA-QSB-016 | 制造商:Embedded Artists 功能描述:BOARD QUICK START LPC4088 |
发布紧急采购，3分钟左右您将得到回复。