- 您现在的位置：买卖IC网 > PDF目录97874 > EB2060X Evaluation board PDF资料下载
参数资料
| 型号： | EB2060X |
| 英文描述： | Evaluation board |
| 中文描述： | 评估板 |
| 文件页数： | 7/12页 |
| 文件大小： | 873K |
| 代理商： | EB2060X |
_______________
__ EB-2060x
4
Details are subject to change without notice.
HEADERS / REGULATORS (FIG. 3D)
The EB-2060x features local power regulation to
facilitate operation from a unipolar +10 to +28
VDC supply. Alternatively, auxiliary power may
be applied at J8 (removing bead L7) separating
logic and output power supplies.
Output from
the onboard +5V regulator is available on the J6
test header.
Output from the onboard +3.3V
regulator is available on
the J7 expansion
header. There is capability available to power
external circuits from either the +5V or the +3.3V
supplies or a combination not to exceed a total
current of 0.33A.
Expansion header J7 is provided to monitor or
apply input signals to the DDX-2000.
Jumper
R42 may be removed to pass serial data
provided by an external processor. Test header
J6 is provided to monitor signals output from the
DDX-2000.
Signals INLC, INLD, INRC, INRD
are driven low by the DDX-2000 and are used
for test purposes only. DIP switch SW1 is used
for control functions:
POS1 reverses data
channels when open, normal when closed;
POS2 sets unity gain for test when closed,
normal when open; POS3 forces the DDX-2060
into low power mode when closed, normal when
open; POS4 disables the anticlipping function
when closed, normal when open.
Supervisor U8 is used for power-on-reset,
power-off sequencing, and as a convenient
means of commanded reset via pushbutton.
ADDITIONAL INFORMATION
Bill of Materials
A bill of materials for the evaluation board is
provided in Table 1 for reference.
Note
equivalent
components
from
alternate
manufacturers may be substituted. No warranty
of system performance is implied by Apogee
through use of the reference bill of materials.
Power Dissipation/Heat Sink Requirements
The DDX-2060 is a high efficiency dual channel
design intended for audio applications needs up
to 35 Watts RMS per channel.
The power
dissipation of the device will depend primarily on
the supply voltage, load impedance, and output
modulation level. The thermal performance of
the evaluation board is consistent with a steady-
state duty rating of 25W RMS per channel with
both channels driven into 8
.
The DDX-2060 surface mount package includes
an exposed thermal pad on the bottom of the
device to provide a direct thermal path from the
integrated circuit to the PCB. This pad must be
soldered to a low thermal impedance path at
circuit ground potential for proper operation, e.g.
a PCB ground plane. For continuous duty rated
applications,
careful
consideration
must
be
made to the overall thermal design.
Performance Measurements
Typical performance measurements for the
evaluation board are shown in Figs 4 through
11.
Class
D
amplifiers
produce
measurable
switching distortion outside the audio bandwidth.
Apogee's DDX amplifier uses a patented PWM
modulation scheme that significantly reduces the
size of these products compared to typical Class
D designs. However, in order to obtain accurate
performance
measurements
in
the
audio
bandwidth (i.e., 20Hz to 20kHz) additional
filtering is required.
The Typical Performance data in was taken
using a brick wall filter with a break frequency of
22kHz. This type of filter is often provided as
part of audio measurement systems.
OPERATING INSTRUCTIONS
Refer to Fig. 12 evaluation amplifier assembly
drawing. Attach a regulated power supply at J3
set between +10V and +28VDC. At +28V, the
power supply must be capable of delivering 3A
minimum for two channels.
Attach a digital
audio input source at either the coaxial or optical
S/PDIF connectors.
Select the digital input
source via J2. Connect 8 Ohm speakers to J4
(left speaker) and J5 (right speaker). Configure
SW1 as POS1 closed, POS2,3,4 open.
Note,
the speaker outputs are bridged. Do not ground
any speaker connections, e.g. through an
oscilloscope.
Apply
power,
digital
source
material
and
enjoy!
相关PDF资料 |
PDF描述 |
|---|---|
| EB402 | EB402 Evaluation Board user＇s guide 7/01 |
| EBD12RB8ALFB-1A | SDRAM|DDR|16MX72|CMOS|DIMM|184PIN|PLASTIC |
| EBD12RB8ALFB-75 | SDRAM|DDR|16MX72|CMOS|DIMM|184PIN|PLASTIC |
| EBD12RB8ALFB-7A | SDRAM|DDR|16MX72|CMOS|DIMM|184PIN|PLASTIC |
| EBD25RB4ALFB-1A | SDRAM|DDR|32MX72|CMOS|DIMM|184PIN|PLASTIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EB2061 | 功能描述:SWITCH PUSHBUTTON DPDT 3A 125V RoHS:是 类别:开关 >> 按钮 系列:EB 标准包装:1 系列:A16 类型:标准，发光式 电路:双刀双掷 开关功能:开-瞬时 额定电流:5A（AC） 额定电压 - AC:125V 额定电压 - DC:- 触动器类型:方形，按钮 颜色 - 致动器/盖:黄 发光类型，颜色:LED，黄 发光电压:12 VDC 安装类型:前面板安装 端接类型:焊接，快速连接 - 0.110"（2.8mm） 防护等级:IP65 - 防尘/防油/防水 特点:- 面板切口尺寸:圆形 - 直径 16.00mm 包装:散装 工作温度:-10°C ~ 55°C 机械寿命:2,000,000 次循环 电气寿命:100,000 次循环 其它名称:A165LAYM12D2 |
| EB-2061 | 制造商:NKK Switches 功能描述:Bulk |
| EB2061-A-J20 | 制造商:NKK 制造商全称:Nihon Kaiheiki Industry Co. Ltd. 功能描述:Light Touch Miniature Pushbuttons |
| EB2061-A-J21A | 制造商:NKK Switches 功能描述:MINIATURE PUSHBUTTON/BUSHING MOU 制造商:NKK Switches 功能描述:MINIATURE PUSHBUTTON/BUSHING MOUNT |
| EB2061-A-J21A-RO | 功能描述:按钮开关 DPDT ON-(ON) RoHS:否 制造商:C&K Components 触点形式:2 NC - 2 NO 开关功能:ON ? OFF 电流额定值:4 A 电压额定值 AC:12 V to 250 V 电压额定值 DC:12 V to 50 V 功率额定值: 安装风格:Through Hole 照明:Illuminated 照明颜色:None IP 等级:IP 40 端接类型:Solder 触点电镀:Silver 执行器:Square 盖颜色: 封装: 可燃性等级:UL 94 V-0 |
发布紧急采购，3分钟左右您将得到回复。