收藏本站
参数资料
型号： EK2550
厂商： Synapse Wireless
文件页数： 40/42页
文件大小： 0K
描述： NETWORK EVAL KIT VERSION 2.1
标准包装： 1
类型： 收发器，SNAP
适用于相关产品： RF300PC1
已供物品： 3 个板，3 根天线，线缆，CD，文档
其它名称： 746-1049
EK2550-ND
Q5101768
Battery Operation
So far, we have been running the nodes from USB power (the bridge node) and from wall
power (the SN111 and SN171 nodes).
It is also possible to run most nodes from battery power.
The SN111 node comes with on-board battery holders, which can hold one or two 1.5
volt AA cells. You have the option of using one or two AA batteries.
NOTE! – The SN111 has a jumper on the right-hand side of the battery holder that
configures the node to run from one AA cell, or two AA cells.
If the jumper is on posts 1 and 2 (the posts furthest away from the battery holder), then
the unit only uses one AA battery, which should be installed in the battery holder closest
to the center of the board. If the jumper is on posts 2 and 3 (closest to the battery holder),
then the unit requires two AA batteries.
Set the jumper to match the actual number of batteries you will be using. Using two AA
batteries instead of one will result in longer operation before having to replace the
batteries.
Regardless of how many batteries are used, be sure to install them in the battery holder
with the correct orientation. The bottom of the battery holder has the usual + and – labels
molded into the plastic.
Note: There is a jumper labeled “RS232 PWR” located near the center of the board.
This jumper must be installed for the RS232 port to work when running on battery
power . To increase battery life it should not be installed if you are not using the RS232
port.
The SN171 Proto Board does not have a built-in battery holder, but a separate battery
holder for this node is included in the EK2500 kit.
Before you can power the SN171 from the external battery pack, you must unplug the
external power supply, and change the PWRSEL jumper located near the center of the
circuit board. The jumper posts for this jumper are labeled “VBAT”, “VCC”, and
“VEXT”. The board comes from the factory with the jumper connected to the VEXT and
VCC pins, which configures the node to run from the external power supply.
If you move the jumper so that it connects the VBAT and VCC pins, then the board will
be configured to receive power from the white two-pin connector located directly behind
the barrel-jack that the external power supply plugs into.
After changing the jumper to the VBAT+VCC position, install two AA batteries in the
external battery holder, and connect the white connector from the external battery pack to
the mating white connector on the SN171 board.
Page 40
of 42
EK2500 Users Guide-v1.7
相关PDF资料
PDF描述
X-10GD SWITCH BASIC SPDT 10A SOLDER
55200C XFRMR CURR SENSE 15A 1:1:200 SMD
55100C XFRMR CURR SENSE 15A 1:1:100 SMD
80-16 NAIL HARNESS BOARD 3.0"
TC25N3I32K7680 OSCILLATOR 32.7680 KHZ 2.5V SMD
相关代理商/技术参数
参数描述
EK25B0012 功能描述:器件套件 Engineering Kit RoHS:否 制造商:AVX 零部件类型:
EK26 功能描述:放大器 IC 开发工具 Eval Kit PA60EU RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V
EK-26597-C36 功能描述:麦克风 5.56 X 3.98 X 2.21MM RoHS:否 制造商:Knowles Acoustics 方向性:Omnidirectional 阻抗:4.4 K Ohms 工作电压:0.9 V to 10 V 灵敏度:- 53 dB 端接类型:Wire Leads 长度:5.56 mm 宽度:3.98 mm 深度:2.21 mm
EK2660-7R 功能描述:EURO-CASSETTE 150W 2X 24V RoHS:否 类别:电源 - 外部/内部（非板载） >> DC DC Converters 系列:* 标准包装:1 系列:Quint 类型:隔离 输入电压:24V 输出:24V 输出数:1 输出 - 1 @ 电流（最大）:24 VDC @ 50A 输出 - 2 @ 电流（最大）:- 输出 - 3 @ 电流（最大）:- 输出 - 4 @ 电流（最大）:- 功率（瓦特）:1200W 安装类型:底座安装 工作温度:0°C ~ 40°C 效率:- 封装/外壳:模块 尺寸/尺寸:4.33" L x 9.09" W x 6.14" H（110mm x 231mm x 156mm） 包装:散装 电源（瓦特）- 最大:1200W 批准:- 其它名称:277-69722866365-NDQUINT-BAT/24DC/12AH
EK2660-9ER 制造商:Power-One 功能描述:DCDC - Bulk
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*