- 您现在的位置：买卖IC网 > PDF目录18779 > EKMB1201113 (Panasonic Electric Works)SENSOR MOTION PIR DIGITAL WHITE PDF资料下载
参数资料
| 型号： | EKMB1201113 |
| 厂商： | Panasonic Electric Works |
| 文件页数： | 8/8页 |
| 文件大小： | 0K |
| 描述： | SENSOR MOTION PIR DIGITAL WHITE |
| 标准包装： | 50 |
| 系列： | PaPIRs |
| 传感器类型： | * |
| 检测距离： | 196.9"（5m）16.4' |
| 输出类型： | 数字 |
| 电源电压： | 2.3 V ~ 4 V |
| 触发器类型： | 内部 |
| 特点： | 聚乙烯，珠白色透镜 |
| 探测模式： | 标准 |
| 其它名称： | 255-3070 |
PIR Motion Sensor (EKMB, EKMC, AMN2, 3)
MOUNTING DIRECTION
1) Detection area
2) Direction
Y
Y direction
As shown on the diagram, the
detection zone is polarized.
If a target enters the
Target
As detailed on the
diagram, please install
the sensor so that the
X
Z
Z direction
detection zones + and ? at
the same time, the signals
expected trespassing
direction corresponds to the
are respectively cancelled
and detection could become
Detection
zone
axis X or axis Y.
In some cases, going back and
X direction
impossible at maximum
detection range.
NOTES
forth towards the sensor (parallel
movement to the axis Z), may not be detected.
1. Checkpoints relating to principal of
operation
PaPIRs is a pyroelectric infrared sensor
that detect variations in infrared rays.
However, it may not detect in the
following case: lack of movement, No
temperature change in the heat source.
Beside, it could also detect the presence
of heat sources other than a human body.
Ef?ciency and reliability of the system
may vary depending actual operating
conditions:
1) Detecting heat sources other than the
human body, such as
(1) Small animals entering the detection
area.
(2) When a heat source for example
sunlight, incandescent light, car
headlights etc, or strong light beam hit
the sensor regardless inside or outside
the detection area.
(3) Sudden temperature change inside or
around the detection area caused by hot
or cold wind from HVAC, or vapor from
the humidi?er, etc.
2) Dif?culty in sensing the heat source
(1) Glass, acrylic or similar materials
standing between the target and the
sensor may not allow a correct
transmission of infrared rays.
(2) Non-movement or quick movements
of the heat source inside the detection
area. (Please refer to the section on the
detection performance ratings for details
about movement speed.)
3) Expansion of the detection area
In case of considerable difference in the
ambient temperature and the human
body temperature, detection area may be
wider apart from the con?gured detection
area.
4) Malfunction/Detection error
Unnecessary detection signal might be
outputted, on rare occasions, come from
sudden outbreak output due to the nature
of pyroelectric element. When the
application does not accept such
conditions strictly, please implement the
countermeasure by introducing pulse
count circuit etc.
For Cautions for Use.
2. Optimal operating environment
conditions
1) Temperature: Refer to the absolute
maximum rating.
2) Humidity degree: 15 to 85%Rh (Avoid
condensation or freezing of this product)
3) Pressure: 86 to 106KPa
4) Overheating, oscillations, shocks can
cause the sensor to malfunction.
5) This sensor is not waterproof or
dustproof. Avoid use in environments
subject to excessive moisture,
condensation, frost, containing salt air or
dust.
6) Avoid use in environments with
corrosive gases.
3. Handling cautions
1) Do not solder with a soldering iron
above 350 ° C 662 ° F , or for more than 3
seconds. This sensor should be hand
soldered.
2) To maintain stability of the product,
always mount on a printed circuit board.
3) Do not use liquids to wash the sensor.
If washing ?uid gets through the lens, it
can reduce performance.
4) Do not use a sensor after it fell on the
ground.
5) The sensor may be damaged by ± 200
volts of static electricity. Avoid direct hand
contact with the pins and be very careful
when operating the product.
6) When wiring the product, always use
shielded cables and minimize the wiring
length to prevent noise disturbances.
7) The inner circuit board could be
destroyed by a voltage surge.
Use of surge absorption elements is
highly recommended.
Surge resistance: below the power
supply voltage value indicated in the
maximum rated values section.
8) Please use a stabilized power supply.
Power supply noise can cause operating
errors.
Noise resistance: ± 20V or less (Square
waves with a width of 50ns or 1 μ s)
To reduce the effect of power supply
noise, install a capacitor on the sensor’s
power supply pin.
9) Operating errors can be caused by
noise from static electricity, lightning, cell
phone, amateur radio, broadcasting
of?ces etc...
10) Detection performance can be
reduced by dirt on the lens.
11) The lens is made of soft materials
(Polyethylene). Please avoid adding
weight or impacts that might change its
shape, causing operating errors or
reduce performance.
12) Operating “temperatures” and
“humidity level” are suggested to prolong
usage. However, they do not guarantee
durability or environmental resistance.
Generally, high temperatures or high
humidity levels will accelerate the
deterioration of electrical components.
Please consider both the planned usage
and environment to determine the
expected reliability and length of life of
the product.
13) Do not attempt to clean this product
with any detergent or solvent, such as
benzene or alcohol, as these can cause
shape or color alterations.
14) Avoid storage in high, low
temperature or liquid environments.
As well, avoid storage in environments
containing corrosive gas, dust, salty air
etc. It could cause performance
deterioration and the sensor’s main part
or the metallic connectors could be
damaged.
Panasonic Corporation
Automation Controls Business Unit
industrial.panasonic.com/ac/e/
ASCTB240E 201208-T
相关PDF资料 |
PDF描述 |
|---|---|
| EKMB1201112 | SENSOR MOTION PIR DIGITAL BLACK |
| ME601615 | DIODE MOD 3PH BRDG 1600V 150A |
| ME501210 | DIODE MOD 3PH BRDG 1200V 100A |
| EKMC1601113 | SENSOR MOTION PIR 170UA DGTL WHT |
| EKMC1601112 | SENSOR MOTION PIR 170UA DGTL BLK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EKMB1201113 | 制造商:Panasonic Electric Works 功能描述:PIR MOTION SENSOR DIGITAL -0.3VDCto 4. |
| EKMB1203111 | 功能描述:板机接口移动感应器和位置传感器 2uA 12m Digital White Lens RoHS:否 制造商:Panasonic Electric Works 封装 / 箱体:TO-5 感应距离:3 m 输出类型:Digital 电源电压-最大:6 V 电源电压-最小:2.3 V 电源电流: 最大工作温度:+ 60 C 封装:Bulk |
| EKMB1203111 | 制造商:Panasonic Electric Works 功能描述:PIR MOTION SENSOR DIGITAL -0.3VDCto 4. 制造商:Panasonic Electric Works 功能描述:PIR MOTION SENSOR, DIGITAL, -0.3VDCto 4.5VDC, 2uA |
| EKMB1203112 | 功能描述:板机接口移动感应器和位置传感器 2uA 12m Digital Black lens RoHS:否 制造商:Panasonic Electric Works 封装 / 箱体:TO-5 感应距离:3 m 输出类型:Digital 电源电压-最大:6 V 电源电压-最小:2.3 V 电源电流: 最大工作温度:+ 60 C 封装:Bulk |
| EKMB1203112 | 制造商:Panasonic Electric Works 功能描述:PIR MOTION SENSOR DIGITAL -0.3VDCto 4. 制造商:Panasonic Electric Works 功能描述:PIR MOTION SENSOR, DIGITAL, -0.3VDCto 4.5VDC, 2uA |
发布紧急采购，3分钟左右您将得到回复。