参数资料
| 型号： | EL1511CLZ-T13 |
| 厂商： | Intersil |
| 文件页数： | 6/18页 |
| 文件大小： | 0K |
| 描述： | IC LINE DRIVER ADSL/VDSL 16-QFN |
| 标准包装： | 2,500 |
| 类型： | 驱动器 |
| 驱动器/接收器数： | 1/0 |
| 规程： | DSL |
| 电源电压： | 5 V ~ 15 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VQFN 裸露焊盘 |
| 供应商设备封装： | 16-QFN-EP（4x4） |
| 包装： | 带卷 (TR) |
14
FN7016.2
April 10, 2007
Applications Information
Product Description
The EL1511 is a dual operational amplifier designed for
customer premise driver functions in DMT ADSL solutions
and is built using Elantec's proprietary complimentary bipolar
process. Due to the current feedback architecture, the
EL1511 closed-loop 3dB bandwidth is dependent on the
value of the feedback resistor. First the desired bandwidth is
selected by choosing the feedback resistor, RF, and then the
gain is set by picking the gain resistor, RG. The curves at the
beginning of the Typical Performance Curves section show
the effect of varying both RF and RG.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Ground
plane construction is highly recommended. Lead lengths
should be as short as possible, below . The power supply
pins must be well bypassed to reduce the risk of oscillation.
A 1.0F tantalum capacitor in parallel with a 0.01F ceramic
capacitor is adequate for each supply pin.
For good AC performance, parasitic capacitances should be
kept to a minimum, especially at the inverting input (see
Capacitance at the Inverting Input section). This implies
keeping the ground plane away from this pin. Carbon resistors
are acceptable, while use of wire-wound resistors should not
be used because of their parasitic inductance. Similarly,
capacitors should be low inductance for best performance.
Use of sockets, particularly for the SO (0.150") package,
should be avoided. Sockets add parasitic inductance and
capacitance which will result in peaking and overshoot.
Capacitance at the Inverting Input
Due to the topology of the current feedback amplifier, stray
capacitance at the inverting input will affect the AC and
transient performance of the EL1511 when operating in the
non-inverting configuration.
In the inverting gain mode, added capacitance at the inverting
input has little effect since this point is at a virtual ground and
stray capacitance is therefore not “seen” by the amplifier.
Feedback Resistor Values
The EL1511 has been designed and specified with RF =
1.5k
Ω for A
V = +5. This value of feedback resistor yields
relatively flat frequency response with <1.5dB peaking out to
60MHz. As is the case with all current feedback amplifiers,
wider bandwidth, at the expense of slight peaking, can be
obtained by reducing the value of the feedback resistor.
Inversely, larger values of feedback resistor will cause rolloff
to occur at a lower frequency. By reducing RF to 1kΩ,
bandwidth can be extended to 70MHz with 3.0dB of peaking.
See the curves in the Typical Performance Curves section
which show 3dB bandwidth and peaking vs frequency for
various feedback resistors.
Power Dissipation
The EL1511 amplifier combines both high speed and large
output current drive capability at a moderate supply current
in very small packages. It is possible to exceed the
maximum junction temperature allowed under certain supply
voltage, temperature, and loading conditions. To ensure that
the EL1511 remains within its absolute maximum ratings, the
following discussion will help to avoid exceeding the
maximum junction temperature.
The maximum power dissipation allowed in a package is
determined by its thermal resistance and the amount of
temperature rise according to:
The maximum power dissipation actually produced by an IC
is the total quiescent supply current times the total power
supply voltage plus the power in the IC due to the load, or:
where IS is the supply current. (To be more accurate, the
quiescent supply current flowing in the output driver transistor
should be subtracted from the first term because, under
loading and due to the class AB nature of the output stage,
the output driver current is now included in the second term.)
In general, an amplifier's AC performance degrades at
higher operating temperature and lower supply current.
Unlike some amplifiers, the EL1511 maintains almost
constant supply current over temperature so that AC
performance is not degraded as much over the entire
operating temperature range.
Estimating Line Driver Power Dissipation in ADSL
CPE Application
The below figure shows a typical ADSL CPE line driver
implementation. The average line power requirement for the
ADSL CPE application is 13dBM (20mW) into a 100W line.
The average line voltage is 1.41VRMS. The ADSL DMT peak
to average ratio (crest factor) of 5.3 implies peak voltage of
7.5V into the line. Using a differential drive configuration and
transformer coupling with standard back termination, a
transformer ratio of 1:2 is selected. With 1:2 transformer
ratio, the impedance across the driver side of the
transformer is 25
Ω, the average voltage is 0.705VRMA and
the average current is 28.2mA. The power dissipated in the
EL1511 is a combination of the quiescent power and the
output stage power when driving the line:
In the power mode, the EL1511 consumes typically 6.6mA
quiescent current and still able to maintain very low
distortion. The distortion results are shown in typical
P
DMAX
T
JMAX
T
AMAX
–
θ
JA
---------------------------------------------
=
P
DMAX
2V
S
V
S
V
OUT
–
()
V
OUT
R
L
----------------
×
+
×
=
PDP
quiescent
P
output-stage
+
=
PDV
S
I
Q
V
S
(
2V
OUT-RMS )
I
OUT-RMS
×
–
+
×
=
EL1511
相关PDF资料 |
PDF描述 |
|---|---|
| CY28442ZXC-2T | IC CLOCK ALVISO PENTM 56TSSOP |
| IDTQS3244QG8 | IC BUS SWITCH 16:8 20-QSOP |
| EL1511CLZ | IC LINE DRIVER ADSL/VDSL 16-QFN |
| EL1508CLZ-T13 | IC LINE DRIVER ADSL 24-QFN |
| EL1508CLZ | IC LINE DRIVER ADSL 24-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL1511CLZ-T7 | 功能描述:IC LINE DRIVER ADSL/VDSL 16-QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL1511CS | 功能描述:IC LINE DRIVER ADSL/VDSL 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL1511CS-T13 | 功能描述:IC LINE DRIVER ADSL/VDSL 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL1511CS-T7 | 功能描述:IC LINE DRIVER ADSL/VDSL 16-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL1511CSZ | 功能描述:IC LINE DRIVER ADSL/VDSL 16-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。