参数资料
| 型号： | EL1519CS-T13 |
| 厂商： | Intersil |
| 文件页数： | 7/9页 |
| 文件大小： | 0K |
| 描述： | IC LINE DRIVER CPE ADSL 8-SOIC |
| 标准包装： | 2,500 |
| 类型： | 驱动器 |
| 驱动器/接收器数： | 1/0 |
| 规程： | DSL |
| 电源电压： | 5 V ~ 12 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
7
FN7017.2
April 10, 2007
Applications Information
Product Description
The EL1519 is a dual operational amplifier designed for
customer premise line driving in DMT ADSL solutions. It is a
dual current mode feedback amplifier with low distortion
while drawing moderately low supply current. It is built using
Elantec's proprietary complimentary bipolar process and is
offered in industry standard pin-outs. Due to the current
feedback architecture, the EL1519 closed-loop 3dB
bandwidth is dependent on the value of the feedback
resistor. First the desired bandwidth is selected by choosing
the feedback resistor, RF, and then the gain is set by picking
the gain resistor, RG. The curves at the beginning of the
Typical Performance Curves section show the effect of
varying both RF and RG. The 3dB bandwidth is somewhat
dependent on the power supply voltage.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Ground
plane construction is highly recommended. Lead lengths
should be as short as possible, below 1/4”. The power
supply pins must be well bypassed to reduce the risk of
oscillation. A 1.0F tantalum capacitor in parallel with a
0.01F ceramic capacitor is adequate for each supply pin.
For good AC performance, parasitic capacitances should be
kept to a minimum, especially at the inverting input. This
implies keeping the ground plane away from this pin. Carbon
resistors are acceptable, while use of wire-wound resistors
should not be used because of their parasitic inductance.
Similarly, capacitors should be low inductance for best
performance.
FIGURE 25. DIFFERENTIAL FREQUENCY RESPONSE vs RF
FIGURE 26. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FIGURE 27. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
Typical Performance Curves
100K
1M
10M
100M
(Hz)
AV=5
VS=±6V
RL=100Ω
RF=1kΩ
RF=750Ω
RF=500Ω
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.4
0
0.8
P
O
WER
DISSIP
A
TION
(W)
0.4
0.2
0.6
1.2
AMBIENT TEMPERATURE (°C)
0
1
25
50
75
100
150
125
85
781mW
θ
JA =1
60°C
/W
SO
8
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY (4-LAYER) TEST BOARD
3.5
3
0
AMBIENT TEMPERATURE (°C)
POWE
R
DI
SSI
P
A
TI
ON
(W)
0150
50
100
2
2.5
1
1.5
0.5
125
25
75 85
1.136W
110°C/
W
SO8
EL1519
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468E17A35S | CONN RCPT 55POS JAM NUT W/SCKT |
| MS27484P22A1S | CONN PLUG 100POS STRAIGHT W/SCKT |
| CS3101A-10SL-53P | CONN RCPT 2POS IN LINE W/PINS |
| M83723/87W1203N | CONN PLUG 3POS STRAIGHT W/PINS |
| HIN202CB-T | IC 2DRVR/2RCVR RS232 5V 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL1519CS-T7 | 功能描述:IC LINE DRIVER CPE ADSL 8-SOIC RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL1519CSZ | 功能描述:IC LINE DRIVER CPE ADSL 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL1519CSZ-T13 | 功能描述:IC LINE DRIVER CPE ADSL 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL1519CSZ-T7 | 功能描述:IC LINE DRIVER CPE ADSL 8-SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| EL151CLZ | 制造商:Intersil Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。