- 您现在的位置：买卖IC网 > PDF目录97898 > EL2030CN 120 MHz Current Feedback Amplifier PDF资料下载
参数资料
| 型号： | EL2030CN |
| 英文描述： | 120 MHz Current Feedback Amplifier |
| 中文描述： | 120 MHz电流反馈放大器 |
| 文件页数： | 2/16页 |
| 文件大小： | 408K |
| 代理商： | EL2030CN |
EL2030C
120 MHz Current Feedback Amplifier
Application Information
Product Description
The EL2030 is a current mode feedback amplifier
similar to the industry standard EL2020 but
with greatly improved AC characteristics Most
significant among these are the extremely wide
bandwidth and very low differential gain and
phase In addition the EL2030 is fully character-
ized and tested at g5V and g15V supplies
Power Supply BypassingLead Dressing
It is important to bypass the power supplies of
the EL2030 with 01
mF ceramic disc capacitors
Although the lead length is not critical it should
not be more the
inch from the IC pins Failure
to do this will result in oscillation and possible
destruction of the part Another important detail
is the lead length of the inputs
The inputs
should be designed with minimum stray capaci-
tance and short lead lengths to avoid ringing and
distortion
Latch Mode
The EL2030 can be damaged in certain circum-
stances resulting in catastrophic failure in which
destructive supply currents flow in the device
Specifically
an input signal greater than g5
volts at currents greater than 5 mA is applied to
the device when the power supply voltages are
zero will result in failure of the device
In addition the EL2030 will be destroyed or
damaged in the same way for momentary power
supply voltage reversals This could happen for
example during a power turn on transient or if
the power supply voltages were oscillating and
the positive rail were instantaneously negative
with respect to the negative rail or vice versa
Differential Gain and Differential Phase
Composite video signals contain intensity color
hue timing and audio information in AM FM
and Phase Modulation These video signals pass
through many stages during their production
processing archiving and transmission It is im-
portant that each stage not corrupt these signals
to provide a ‘‘high fidelity’’ image to the end
viewer
An industry standard way of measuring the dis-
tortion of a video component (or system) is to
measure the amount of differential gain and
phase error it introduces A 100 mV peak to peak
sine wave at 358 MHz for NTSC (43 MHz for
PAL) with 0V DC component serves as the refer-
ence The reference signal is added to a DC offset
shifting the sine wave from 0V to 07V which is
then applied to the device under test (DUT) The
output signal from the DUT is compared to the
reference signal The Differential Gain is a mea-
sure of the change in amplitude of the sine wave
and is measured in percent
The Differential
Phase is a measure of the change in the phase of
the sine wave and is measured in degrees Typi-
cally the maximum positive and negative devia-
tions are summed to give peak differential gain
and differential phase errors The test setup in
Figure 1 was used to characterize the EL2030
For higher than NTSC and PAL frequencies an
alternate Differential Gain and Phase measure-
ment can be made using an HP3577A Network
Analyser and the setup shown in Figure 2 The
frequency response is normalized to gain or phase
with 0V DC at the input From the normalized
value a DC offset voltage is introduced and the
Differential Gain or Phase is the deviation from
the normalized value
Video Applications
The video signals that must be transmitted for
modest distances are usually amplified by a de-
vice such as the EL2030 and carried via coax ca-
ble There are at least two ways to drive cables
single terminated and double terminated
When driving a cable it is important to termi-
nate it properly to avoid unwanted signal reflec-
tions Single termination (75
X to ground at re-
ceive end) may be sufficient for less demanding
applications In general a double terminated ca-
ble (75
X in series at drive end and 75X to ground
at receive end) is preferred since the impedance
match at both ends of the line will absorb signal
reflections However when double termination is
used (a total impedance of 150
X) the received
signal is reduced by half therefore the amplifier
is usually set at a gain of 2 or higher to compen-
sate for attenuation
10
相关PDF资料 |
PDF描述 |
|---|---|
| EL2033CN | 100MHz Video Line Driver |
| EL2044C | Low Power/Low Voltage 120 MHz Unity-Gain Stable Operational Amplifier(低功耗，低电压 120MHz单位增益稳定运算放大器) |
| EL2044 | Low Power/Low Voltage 120MHz Unity-Gain Stable Operational Amplifier |
| EL2044CN | Low Power/Low Voltage 120MHz Unity-Gain Stable Operational Amplifier |
| EL2044CS | Low Power/Low Voltage 120MHz Unity-Gain Stable Operational Amplifier |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EL2030D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Feedback Operational Amplifier |
| EL2030J | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Feedback Operational Amplifier |
| EL2030J/883B | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Feedback Operational Amplifier |
| EL2030L | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Feedback Operational Amplifier |
| EL2030L/883B | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Current-Feedback Operational Amplifier |
发布紧急采购，3分钟左右您将得到回复。